Search:

Type: Posts; User: BoatBuggy

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    64
    Views
    2,447

    I'm almost wishing one of my SHO's would blow up...

    I'm almost wishing one of my SHO's would blow up so I would have a reason to get the new one. That's one great looking engine.
  2. Replies
    4
    Views
    148

    My favorite Jackhammer rod is the Gen 1 Orochii...

    My favorite Jackhammer rod is the Gen 1 Orochii XX Diablo Spec-R. I have 3 of them. For reasons I can't really pinpoint I don't like the current DS-R for Jackhammers. If was buying another Jackhammer...
  3. Gear up for both shallow (< 5 ft) and deep (> 25...

    Gear up for both shallow (< 5 ft) and deep (> 25 ft) but my best results in the few times I've gone out at that time of year has been more deep. I don't recall catching smallies in the mid-range but...
  4. First thing I would do is bypass the Y-cable and...

    First thing I would do is bypass the Y-cable and in-hull transducer. If a transducer or cable is going bad, it can make the unit do some weird stuff.
  5. Traffic Question For Chattanooga Area BBC'ers

    What time do we need to be going through Chattanooga before morning rush hour traffic starts to pile up? We are starting the day just east of Birmingham and our route is I-59 North to I-24 East to...
  6. Replies
    46
    Views
    2,451

    Thanks for sharing! :thumb up2:

    Thanks for sharing! :thumb up2:
  7. Replies
    9
    Views
    181

    I have a NOCO 3x10 to charge the TM batts and a...

    I have a NOCO 3x10 to charge the TM batts and a NOCO 2x10 for the electronics batt and to top off the cranking batt. The charger lead on the cranking batt is more a spare than anything as I rarely...
  8. Replies
    6
    Views
    276

    Since you are re-doing your battery setup, don't...

    Since you are re-doing your battery setup, don't plan on running excess wire and instead install a Blue Sea grounded fuse block around the console area and run 6 ga marine tinned between the fuse...
  9. Thanks Wayne. I missed the US2 part of the...

    Thanks Wayne. I missed the US2 part of the original post.
  10. Essentially what I did except replaced a Lowrance...

    Essentially what I did except replaced a Lowrance with an Echomap. You'll have to mess around with the proper heights for M360 and the LVS-34 xducer. My M360 sits maybe 2" below the surface of the...
  11. Replies
    32
    Views
    1,650

    Nice!!!!! :thumb up2:

    Nice!!!!! :thumb up2:
  12. I have HBs and Echomaps at both the bow and...

    I have HBs and Echomaps at both the bow and console. No one else has anything comparable to Mega 360. Also, being in TX you might want to keep Lakemaster maps esp if you fish Rayburn and Toledo. I...
  13. Replies
    14
    Views
    817

    I guess it's because Tulsa is footing the bill.

    I guess it's because Tulsa is footing the bill.
  14. Replies
    6
    Views
    326

    I use the little ring that gets created when a...

    I use the little ring that gets created when a water bottle or soda bottle is opened. They don't take up much room, aren't very heavy and if I lose it in the boat, all I have to do is open another...
  15. Nah......

    Nah......
  16. Even though I have a Carbon on a boat, I don't...

    Even though I have a Carbon on a boat, I don't really know much about Lowrance transducers other than you can swap between 455 and 800 kHz on the imaging and I think it's 80 and 200 kHz on the reg...
  17. 1. Your Lowrance transducers at the back will not...

    1. Your Lowrance transducers at the back will not interfere with M360 or MDI at the bow.
    2. Not familiar with Forward Live Sight but from what I can gather it runs at 455 or 800 kHz so you should...
  18. Replies
    6
    Views
    157

    Interesting. I have zero issues using a Point 1...

    Interesting. I have zero issues using a Point 1 with my Helix 10 G4N or Helix 12 G4N other than not being able to figure out how to disable NMEA2K engine messages appearing when I turn the engine off.
  19. Replies
    17
    Views
    702

    I have had all 3 on my boat at the same time....

    I have had all 3 on my boat at the same time. Today I run both ML+TL and LVS-34 (and Mega 360).

    If you are fishing open water chasing stuff around or casting at what you see, they are all...
  20. Replies
    14
    Views
    246

    I would have tried the big ol' bucket if I had...

    I would have tried the big ol' bucket if I had one big enough that I could entirely submerge the TM head and ML xducer.
  21. Replies
    14
    Views
    246

    I'm not Wayne but I couldn't reproduce it with...

    I'm not Wayne but I couldn't reproduce it with the wet towel. I had to go out on the water. But I would certainly try the wet towel first.
  22. Replies
    14
    Views
    246

    You have the symptoms of an older Mega Live...

    You have the symptoms of an older Mega Live transducer that needs to be replaced. HB has been replacing them as required free of charge but you will probably need to contact them again and send them...
  23. The 4 bolt pattern is the same but there are 2...

    The 4 bolt pattern is the same but there are 2 more holes for the Quest and you might have to make the existing holes a little bigger.
  24. Thread: Ring Free

    by BoatBuggy
    Replies
    7
    Views
    999

    I've always found PartsVu to have the been about...

    I've always found PartsVu to have the been about the cheapest. The last order I made back in Dec, the 12 oz bottles were cheaper per oz than the 32 oz bottles.
  25. Thread: I Love You!

    by BoatBuggy
    Replies
    138
    Views
    3,123

    :praying:

    :praying:
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4