No
Type: Posts; User: stickmanc
No
Scott, have you checked for fire on all cylinders yet?
Airxsteel, mine is an 84 and I believe the manual says to tighten the castle nut with your fingers till snug and then tighten to the first hole for your cotter pin. I'll check the manual when I get...
I used a small chain hoist when I changed my powerhead gasket. Took a little bit of effort to get the powerhead off the mid with that old gasket. I would not have liked doing it by hand.
Where did you get the powerhead from?
Look at the top of this forum, go to the Johnson Evinrude on-line Parts catalog and type in your model # http://xs-s.com/zf/images/smile/emthup.gif
Congrats on the boat http://www.bassboatcentral.com/boardstuff2/beers.gif . After you get a chance to enjoy it, I'd love to see some closer pictures of the motor. So I take it he unhooked the VRO...
My friend has a 96 Hydrasport F/S 185 and I'd bet money it has 16oz http://xs-s.com/zf/images/smile/embeer.gif
What year boat and brand? I just did mine with 20oz. from bassboatcarpets and had no issues on an 87. Yes the floor was a pain, but I have a F/S with a walkthrough. That may have been the difference,...
You have OMS part#5004558, yes you can buy parts.
Compression gauge, gauge readings will vary. If that is so the compression is higher than mine.
There you go http://www.bassboatcentral.com/smileys/bows.gif
Here are some pictures of mine. It is an 84 and it has the VRO ( should have a VRO decal on the front of the motor. I disconnected mine only because I haven't spent the money ( approx. $300 ) for the...
Pictures???? http://www.bassboatcentral.com/smileys/crying.gif
hopefully these will help
http://im1.shutterfly.com/procserv/47b6d924b3127cce8ae71c89a74d00000016108AbtGzdizaOF
http://im1.shutterfly.com/procserv/47b6d924b3127cce8ae71d74661800000016108AbtGzdizaOF...
Mike, if nobody jumps before I get home I'll send you the wiring diagram.
Thanks Mike, inspiration and knowledge from this board is the only reason I attempted it in the first place. http://www.bassboatcentral.com/smileys/wink.gif
Thank you gentlemen, but believe me the camera does not catch everything. I am glad that I did it though http://www.bassboatcentral.com/boardstuff2/beers.gif
http://im1.shutterfly.com/procserv/47b6d925b3127cce8afc3afadf4b00000016108AbtGzdizaOF
http://im1.shutterfly.com/procserv/47b6d925b3127cce8afc3af95e7800000016108AbtGzdizaOF
...
http://im1.shutterfly.com/procserv/47b6d925b3127cce8af13910bf7700000016108AbtGzdizaOF
http://im1.shutterfly.com/procserv/47b6d925b3127cce8af1391ebf7900000016108AbtGzdizaOF...
If the man has natural gas ( not the Bud Light kind ), find out the direction of the line to his meter and make a midnight run with some ROUNDUP. He'll get tired of paying the gas company to come out...
Yes I did use contact cement on the lids.
When using the carpet glue, is it thick enough to hold the carpet in place while it's waiting to dry?
http://forums.screamandfly.com/forums/attachment.php?attachmentid=57996&d=1082750180 http://www.bassboatcentral.com/smileys/roll.gif http://www.bassboatcentral.com/smileys/roll.gif ...
Mike, I went down to the local marine and borrowed their flaring tool for about 1 hour and they had no problem with that. I offered to leave my drivers license. I used 4200 and the tubes were...