Update
Update
Well I did find water in the Lu. I did clean that up but I probably need new seals ect. And probably just replace the magnets and plate and wires and the armature looks good...
Type: Posts; User: muskyhunter
Update
Update
Well I did find water in the Lu. I did clean that up but I probably need new seals ect. And probably just replace the magnets and plate and wires and the armature looks good...
Yes a load tester is what I used and all wire connections are clean. Check under head no problems there I did clean out the motor when I found water in there cleaned up magnets and armature too...
Trying to figure out what is going on with my terrova 80 60 inch shaft. I have full battery my charger is showing full charge on both battery’s and I have checked them with a battery tester and...
well I did not let them cool like that. Wish I would have known that trick. I did let them cool on their own and they closed up good. I also used a iron out to o clean them up a bit I do have a...
No I didn’t know about that part of the test. I did watch them close on their own just cooling off
I have done that already I water pan tested them and they both opened up at 130. And on the motor they both go up to 130 then it starts dropping as I can watch them with the infrared thermometer...
Ok update I changed the plugs they were original still had black paint on them. Except for the one that Sherm replaced it really seems so much smoother. And I’m getting spark as far as I can tell....
ok today I stopped at harbor freight and got a timing gun. Found no spark on bottom left coil. Tomorrow I will pull the plug and check to see if it went bad and swap coils and see it it’s the coil. ...
yes it was Sherm My serial number is OTO90851 2000 optimax 225 running a 21 p tempest plus 5750 limit rpm’s now this motor was replaced in 03 by mercury with added smartcraft
I kinda tried that didn’t seem to help once it got back up to limit it would do out again
It is kinda slow it doesn’t throw us too much it will go from 50 to 45 then after a few it will go back to 50 It is kinda quick. I will say a few years ago I was loosing all power and Sherm...
Well it will top out rpm’s at the limit then back down. My boat is a heavy ranger and it usually runs about 50 but when this kicks in it will back me down to 44to 45
<0T090851>
Been having a problem with my 2000 opti 225 she gets out of the hole fast I can run wide open and get to the 5700 limit. Then it seems to godown to around 5000 and slows down tgen...
I would like to know that too as I have to replace the button pads on my 8 gen 2 also
I’m having the same problem on my 8 gen 2 what board did you check that was giving you the problem I’ve try everything and I’m still getting no source. All lights are working on the box and I have...
I know this when I was out this weekend on the water. The transducer did see bottom is stays solid green. I guess that means something
I already got another cable. It still does the same thing. Still says no source. And all lights are working on the sshd box have no idea what’s going on or if I did something wrong
when I ran...
Well I tried another cable. No good I’m still getting a no source
I hope too. All lights are working and I can hear the transducer ticking too it is showing Ethernet lights but the unit isn’t getting it
Ok I have a guy sending me one. It’s used but he said it’s good it’s the black one too
I have done that several times now. Even after updating to the 4.0 from the 2.0 and it didn’t work on that software either. How do I post a pic here
The source will not highlight I cannot choose anything
I have the HD module but there is no place to highlight to check mark that. Just side scan on the advanced area. I check marked the side scan that is what I was told
Ok I have a question about my hds 8 gen 2 I still don’t have side scan I have not tried a new Ethernet cable as I cannot find one local. But I did listen to the transducer with a stethoscope and...
Well I hope it’s the cord today when I got home I checked the pins on the cord with a continuity tester and all the pins seemed to work. Now I’m hoping it’s not the box or transducer