Looking for a couple of the rail mounts , let me know if you have any want to sell.
thanks
Type: Posts; User: Sundby
Looking for a couple of the rail mounts , let me know if you have any want to sell.
thanks
Looking for new or like new bundle. Thanks
Wanted- like new condition. Thanks
Needing the gimbal mount and knobs for a carbon 9. Let me know if you have one.
thanks
Found one. Looking for a carbon 9”, with cover and gimbal mount- don’t need transducer.
let me know what you have. Thanks
Serial# 0G412145
Hi, I am having a hard time getting my 1996 25hp mercury 2 stroke tiller, non electric motor started on initial startup, usually takes 30-40pulls, then will fire, after that all day...
On My boat I Run the 3 or 4in Wide Packing tape, sprayed the boat with windex under the rub rail, ran the tape all the way around, used a credit card to get all air bubbles out, let it dry. has never...
250 Mercury verado- 2b028186
Hi, I have a 2014 250 Mercury verado , what is recommended rpms wot for the verados?
i have a fast prop that runs about 6150-6200 rpms , is this okay to run at?
thanks
don you were right when you said properly connected, I bought this boat used, soo, when I turn the verado off and fire up the 9.9 kicker I have no power steering, I am guessing these just need to be...
Buddy of mines gauge wasn't working the other day, we looked in the jackplate and the L bracket was broke from a small stick, cheap plastic in my opinion.
Okay will do! Thanks
Any pics?
250 verado- 2bo28186
ranger 620
i had my ranger dealer (300 miles away) install a 6" hyd atlas jackplate, they did a terrible job. I'm going to try and finish it correctly, my question is what is...
Yeah, ranger dealer, only 2 in the state of ND, Both are 300 miles away. I will re do it myself and let them know my disappointment, don't want to haul back there, I just need the correct parts.
must have been first day my luck I guess, that's what I was planning on doing with the cover bracket and longer bolts, but , the motor hydraulic cylinder already is hitting the nut/bolt at full turn....
So i have a few more questions, I'm going to call dealer tomorrow and get correct washers that i need and i probably need longer bottom bolts and i should tell them i want my 200$ back for redoing...
Will do, thanks guys.
You got that right, I also noticed on the inside of the jackplate where the jackplate is mounted to the transom, the bottom bolts, there's 2 bolts on each side, instead of using the right size...
No, there's plenty of room for washers, looked at some pics of my old boat with same plate had washers, just looked at my buddies boat has washers, I guess the tech didn't feel like going to find...
I just got my atlas 6" hyd jack plate installed on my ranger 620 and got it home from dealer, 3hrs away, I noticed we. I got home they didn't use any flat washers on the 4 bolts inside of the plate...
There not a huge deal, but I think I will get a kit from ranger and just fill it in the best I can.
I have a couple small small chips in the top edge of my gunnel on my ranger 620 there a couple feet apart, I was wanting to get fixed, fiberglass professional quoted me 500$ to get them repaired,...
What are your rpms running at now? Could be rev limiter, if you got the tune I would think you would need to go up in pitch, I could be wrong.
2014 ranger 620
250 Mercury pro verado
6" atlas hydraulic jackplate
9.9 Mercury kicker
Minnkota terrova ...
Does anyone have one of these installed in there boat? Just curious how well they work and if they can cause any handling issues, I haven't really had a chance to get my boat out, but I bought the...