I have several Gen 1s that are maintained regularly, but I have 1 that the spool runs the windage adjustment on the left side (opposite side of the crank). I can’t for the life of me figure out why...
Type: Posts; User: bdub
I have several Gen 1s that are maintained regularly, but I have 1 that the spool runs the windage adjustment on the left side (opposite side of the crank). I can’t for the life of me figure out why...
Thank you. I picked up the adapter from Cabelas today and can hear the transducer clicking now. Hope to get this thing in the water tomorrow. First impressions are good so far. Feels more solid...
My Ultrex bit the dust so I upgraded to the Quest. Reading on Minn Kota Website I found where someone had asked if Lowrance was able to use built in transducer to which support replied as long as...
Pm sent
Anybody want this middle seat from my previous 20 XS? I don't have the boat anymore, as it was totaled in a car wreck. I was however the original owner, and this seat was never on boat. $75 plus...
Thanks. I kind of thought moisture in switch too, as I watch my voltage like a hawk through the Powerpole Charge app. Never an inkling to low voltage, this was more like some flipped the wrong light...
It's the X2 from Batteries Plus. 3rd one I've had and 6 months old. No issues till today and not flickering of graphs on startup of motor.
My outboard is a 2012 I believe maybe a 2011 as it's on a 2012 Phoenix. Anyways while fishing in rain today my boat lost all electrical power today 3 times while I was using the trim. Twice while...
Thanks Don
Thanks. My outboard is wired through the main breaker switch along with everything else landed on that bolt that is glassed in so I can isolate everything while the onboard charger is on. That is the...
Need some electrical wiring help. I'm wanting to rewire my setup to make it more user friendly. Over the 10 years of owning my boat, accessories have been added. The boat has a "positive" bolt that...
I found that too with a Google search, but if you try to navigate to their flurocarbon line on the website it is hidden.
https://www.berkley-fishing.com/collections/fluorocarbon-line
Was browsing the Berkeley website today looking to see if any of the new stuff from iCast was avaliable and noticed that 100% flurocarbon wasn't listed anymore. They have leader line in it only. Is...
Don,
Not to high jack the post, but what can cause a wet plug? I lost a coil pack on my '12 250 ProXS (#3 cyclinder) so decided to do tune up while I was in there (plugs and fuel filter). My #4...
Have the genuine Garmin perspective mode mount installed, and when it is perspective mode the depth will not read. In down or forward mode it will. Ive seen lots of videos where the user's depth is...
So I've had forward facing livesight on my boat for a few trips now and have been able to catch fish out in front of the boat in open water that I would have never known were there without it. Is it...
Thanks Wayne. I'd like to have 360 off the trolling motor (as in 360 xducer hanging off trolling motor not transom) in the future so a DI unit would be needed up there.
I would use 2 units at the...
Wayne those might be the most informative responses I have ever gotten in here. Thank you for that.
My current setup I have an Ultrex with remote, but no ipilot link...didnt need it with my...
I think I'm going to switch to Humminbird and need some help in selecting units. I'm pretty sure I want to go to Helix over Solix units due to the difference in power consumption and running 3 units...
Been lots of discussion in the past about quicksilver fuel treatment products, but I can't find anything about quickare when running non ethanol gas. I run quickleen with every tank, but curious if I...
Thanks for the tip. Went and got some tape and worked perfect.
Anybody using this?
https://www.mercurymarine.com/en/us/news/mercury-marine-to-release-new-flo-torq-propeller-hub-system/
Will it fit a torque master gear case? The old black one, not the new...
That's weird. The hub kit that is on there looks exactly the same as the one you are posting just with a differnet part number. Wonder what the difference is? Same washers and everything.
That is what is on there now. The part number on the hub is 840237-C. After searching part numbers it seems the pic you posted with the part number on the box has the 840237-C part number sleeve...
I need some help with getting the right flo torq assembly for my proxs. It is a 2011 250 proxs with the torque master gear case. It is the older gear case....not the gray one. The flo torq assembly...