Will need a 23 fury or 24 tempest plus. Fury stiffer than tempest, is the reason the size will not match. Fury will also run deeper than tempest. Prop height is the same as 2 stokes, but top rpms is...
Type: Posts; User: BuddyT
Will need a 23 fury or 24 tempest plus. Fury stiffer than tempest, is the reason the size will not match. Fury will also run deeper than tempest. Prop height is the same as 2 stokes, but top rpms is...
That's the correct way to install wedges. Think about it if jackplate was installed 1st the jackplate wound follow the sam's degree angle of the transom. By installing the wedges 1st. The jackplate...
The graph on the bow must be connected to NEMA to read the Point 1.
The one point that everybody missed is the op is running TI units. Since TI units will not network with Carbon or Live units it does not matter which way he goes. Live scope or Garmin will have to...
I'm a USMC Vet also, but that's not why I'm answering this thread. I just got though testing a Pro Max 24 inch pitch on my 2012 21HP. I have a 300 Pro XS 4 stroke so your pitch numbers will be...
Yes I meant a Pro XS.
I have a 300 Pro Max on a 2012 21 HP. Boat is tournament loaded and has 4 group agm battery's and runs mid to upper 70's with 24 inch pitch Fury 4 prop. I have ran a bunch of different props and have...
I have a 2012 21hp with a 300 Pro Max. I run a 24 Fury 4 and a 24 Pro Max prop. I have 2 degree wedges installed on the 10 inch atlas jackplate. The Fury 4 has better stern lift and ok bow lift, the...
Go to bass boat set up forum, they have a sticky on how to measure prop to pad. Helps to have a helper when leveling the pad, or you will crawling out from under the boat a bunch.
One other thing to add, you didn't see where you mentioned what boat brand you have. On a CMS v8 the hot foot matters which kind you have. Ranger found that the top loading hot foot, the model which...
You got problems, and I would suspect tach as mentioned. Mercury slip calculator is showing 21.05 percent slip, and that is figure with 25 instead of 26. A 3 blade Fury runs stiff compared to a...
The 26 tempest prop is the go to prop for 21 foot tritons with 250 pro xs. Mine came with a 25 Fury that suck every where except holeshot and topend. I went to bravo xs with the optimal and liked...
Don't know about a 26 Tempest, though it should run about the same rpms as a 25 Fury 3 blade. I had a guy who runs a go fast bass shop do prop testing this past winter for me. He's the one that got...
Don't have a 300R but do have a 300 ProXS. My boat is a 2012 21HP, had a 250 ProXS on it when I bought it in 2015. Had over 600 hours, air compressor when out in April 2020, 1300 dollars and nearly...
Your welcome. I served 31 years between active duty and reserve/national guard. I really appreciate when people thank me for serving. Thank you for remembering.
Sorry to jump the thread, but can the drawer be retrofitted to a 2012 21 HP, has the same looking poly plate?
I have had several conversation with two guys, Scott Reichow and Rick Mackie, from Mercury Racing. The Bravo XS props when casted are all made with even pitch 1 inch apart: ie 24,26,28. When they...
Yea go to this websites, https://www.zoro.com/epdm-rubber-seals/c/10274/. That have all different type and size, also they have some different types with the Aluminum Clip. I have not order any from...
Your description matches the 2.5 liter EFI shop manual that I have, look at the Torque Master and CLE lower units. Books says 1st seal lip down, towards rear gear, 2nd seal lip up. Use mandrel big...
Trimlok.com and zoro.com has the correct trim, just measure the size you have and figure out how long you need and order from them.
BuddyT
In my 2012 21HP the Omi Bus module is mounted on the driver side in the battery compartment.
I have 2012 21HP Elite with a 250 Pro XS, with 10 inch Hydraulic jackplate. Pick the boat up in Kentucky 2 years ago. Boat had a 25 Fury on it when I got it. Didn't like the way the prop carry the...
This is some interesting conversations going on here. When I went to a Bravo I text Scott Reichow, who is the designer of the prop for Mercury Racing. I asked him about the slip that I was getting,...
Bought a new to me 2012 Triton 21HP up near Cleveland, and pulled it back with my wife 2012 4runner, keep the auto transmission in 4th in the hills on the way back to Arkansas. I was totally happy...
Friend on mine name Gentry put 2 Talon on his Triton last year, 3 weeks ago blew out a cable and the only way to get the boat back to the ramp was undo the tilt and lay it down in the boat for the...