Model E250LHAGF Serial # 5484946.
When I come into a no wake or get ready to stop to fish a spot, going from high rpm's, trimming down, and then coming out of the throttle. My engine may or may...
Type: Posts; User: SebastJO
Model E250LHAGF Serial # 5484946.
When I come into a no wake or get ready to stop to fish a spot, going from high rpm's, trimming down, and then coming out of the throttle. My engine may or may...
Also, another issue that I probably should've mentioned, and I just bring this up because maybe there is some sort of correlation... The boat will also cut off, like you pulled the kill switch...
bighare. They said they checked that out and everything was good there. Any idea what could be the next item to check? I was really hoping that was my issue. IDK if this matters at all, but this is a...
bighare should this be throwing a code? I'm not getting a code at all. Also, on the RPM's, I could've swore that I read in the owner's manual that max RPM range was 5400-6000. Is this incorrect?
1badair I don't think this is it. I tried "feathering" it up and it led to the same results. It's still a delay.
WOT RPM's tricky question... It has a hydraulic jackplate. I have moved that all over the place. I'm going to say 5,950-6,000. I honestly haven't maxed the boat out yet. The DPS is a little different...
bighare the powerhead was replaced by the dealer under warranty. 195 hours on it now. I just bought the boat with the new powerhead installed. I can't give a fair answer here. I'm going to say that...
Model E250LHAGF Serial # 5484946. When I mash the foot throttle to plane out, my boat is not taking much throttle at all. It will just sit there nose high for about 5-10 seconds, then take off...
Thanks for the info. I feel confident that my mechanic will work on the motor for me as needed. They may not service them, but he will service it for me. That part isn’t an issue. That being said, I...
I'm looking at a boat that has a 250 G2 on it(Blown up with 190 hours). Boat is getting a new powerhead and has roughly three years of warranty left. Thoughts on Warranty, parts availability, resale,...
2011 SHO. (New bulb, and new fuel filter in the hull, mechanic thought this could be the issue) anyway, so I’ll pump the bulb before my initial takeoff (bulb seems to be losing prime when sitting for...
I’m running synthetic oil so far, but I have read about running the lower grade oil. I suppose I’ll run that through it next. I’m running 5,900-6,000 RPM’s so I really don’t feel like that’s a...
I followed the Yamaha break in procedure to a T over the winter and have ran the boat as hard as possible since then. It was replaced new at 185 hours. Currently sitting on 220 hours. Can’t seem to...
New powerhead replaced under recall. Running a 2011 21FX w/ 25-T1 prop. I'm running out about 74.6 with a decent fishing load, but I'm occasionally bumping 6100 at times. I've seen numerous...
Yes. Mine is being replaced right now.
Thanks for the info! If higher octane is the right choice, I'll go higher octane. lol. Probably be doing it myself honestly.... Time permitting. I'm no expert, but I've felt like in the last few...
Thanks!
Thanks a lot for the input. I don't put mine up for the winter. I fish it all year in KY, but generally about the time I do maintenance as well. I have a new to me 2011 21FX skeeter. I just want to...
So I'm New to Yamaha and really to the Yamaha portion of BBC I guess.. Sorry if I do not post something correctly. Coming from Mercury 2 stroke to Yamaha 4 is going to be a little different for me....
Seriously looking at buying a 2011 21 FX I found, it has a 250 SHO on the back. I have a few questions. It's been treated a little bit rough. What's my best option on fiberglass fender...
Ok. Update. From what I can tell, the water pump replacement fixed the issue. Ran it on the muffs last night and seemed to have plenty of water pressure and a nice stream spraying out. That being...
OH yeah, always have and never do a lot until I have his input. After all, the guy is basically the Mercury motor bible. I just wish I lived close enough for him to work on my motor. lol
Ok, I got a guardian shut down at idle speed w/overheat when I tried to take off. Made a long run prior to all of this happening and. Water pressure and temp was fine then. I’m thinking a few mins of...
Drained lower unit grease, just because. Gonna let that sit and drain good. Pulling lu tomorrow and find out what the impeller looks like. Changing it either way of course, hopefully that’s the...
It’s not the strainer. Just got it out a few minutes ago. Little bit of crud in there, but not much.