Thank you for your help. I've been working with Navionics and they are sending me a replacement card at no cost. That is outstanding customer service.
Type: Posts; User: 91@Storm
Thank you for your help. I've been working with Navionics and they are sending me a replacement card at no cost. That is outstanding customer service.
Unfortunately no. This is the only unit I have. Seems odd that when the card is removed everything works fine.
Having issues with my navionics card and my Simrad. The unit will power off for no reason and once turned back on it will turn back off. If I remove my navionics card the unit will work all day with...
1998 225 EFI
serial number 0G723446
recently had my powerhead rebuilt and am in the process of finishing the break in. I’ve noticed that my water pressure is not as high as it was prior to the...
1998 Mercury 225 EFI
Serial # 0G723446
I'm wanting to test and adjust my throttle position sensor and am hoping someone can point me to the correct TPS harness.
I ordered and am waiting on...
Looking to repower my boat after my current 98 225 EFI lost compression in the number 3 cylinder. Hoping someone can shed some light on the "bad" years of the optimax.
I have found a 2003 225...
Well, my 98 225 EFI ( 0G723446 ) lost power last weekend during a tournament. We made it back to the ramp and once home completed a compression check to find no compression in one cylinder. I pulled...
1998 225 serial number 0G723446
I am looking at purchasing this motor and it will not come with the remote oil tank. My question is, would you run the oil injection on this motor or premix 50:1....
You know I never thought about the hole shot with the bigger prop. I'll stick with what I have. For a boat of this size to run as well as it does I am all smiles. I have seen 67 MPH by myself @ 5800.
Tournament load, 2 people with 25 gallons of gas and 1/2 full livewell it runs 64 MPH ( GPS ) @ 5,800 RPM. The motor has a Bob's Exhaust tuner, Brucato ACU, Chris Carson Reeds and injectors cleaned...
I question the tach also but need to find away to verify it.
So, I picked up a new 24 pitch Tempest plus and turns out that I really need to be running a 25. My RPM's are roughly 300 - 400 over the 5600 max for my 1998 150 EFI. My question is, do I sent this...
I have the solid mounts in my 98 150 and haven't had any issues.
I want to say it was $1,500. Tony will be able to add a tune to the ACU that will also help the motor run better. I sent them my ECU and they checked it out while cleaning my injectors. The fuel...
You can also look at Brucato for a replacement. I ended up going with a Brucato ACU on my 98 Merc 150 and couldn't be happier.
Thank you.
How could I test the alarm?
1998 Merc 150 EFI
Serial # 0G624081 / Oil injection removed.
I am in the process of rigging my motor on a new hull. The previous motor was a Yamaha and I am replacing with my Merc 150. My...
The carb rebuild would be my first place to look. If the floats were not set properly the motor would be low on power and use a lot of fuel.
Well, once I removed the fuel rail I found that someone had placed two different injectors in. Two with white tips in the top and four with the needed pink tip. So, cleaning has been put on hold unit...
Thank you Don, I'm thinking I may send in the injectors and fuel rail for a cleaning while I'm working on it.
Serial number 0G624081
I picked up this motor and have ordered a factory service manual. While I am waiting for the manual to show up I was wondering if someone could help with a few questions. Is...
Hopefully Don can help us out.
The serial number on my motor is A 926583 and the WOT RPM range is 5500 - 6000. I run a 19 pitch Tempest that keeps the RPM around 5,800.
I have the same box on my 86 150 and want to remove it but am unsure of the timing change. Hopefully someone can help us out on this.
Thank you for the info. I replaced the cranking battery today and decided to give it a try. I filled the engine mounted oil tank and hit the key a few times and she fired right up. The motor was...
I picked up a 89 SF 175 with the matching Yamaha Pro V 150 this week. The boat has no jackplate and I am planning to add one. Does anyone know what set back I should be looking at 6, 8, 10?
the...