Search:

Type: Posts; User: Rudeman

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    13
    Views
    574

    I mounted mine on the rear stbd corner on the...

    I mounted mine on the rear stbd corner on the gunnel. I wanted to get it as close to the rear transducer while avoiding motor interference AND still have good line of sight. In its current position.,...
  2. This one is identical to the one that it will...

    This one is identical to the one that it will replace.
    ...
  3. Replies
    3
    Views
    227

    I used DAP Contact Cement. It's on pretty solid....

    I used DAP Contact Cement. It's on pretty solid. Coat both sides and apply the mat when the cement is tack free. Then pull it up and quickly reapply it.
  4. Replies
    16
    Views
    1,032

    When I bought one for my 361V back in 2005, it...

    When I bought one for my 361V back in 2005, it included a mounting bolt, nut and washers.
  5. Replies
    48
    Views
    4,801

    PM sent

    PM sent
  6. Replies
    7
    Views
    161

    Can you post a couple of photos?

    Can you post a couple of photos?
  7. Bigger wheels would mean shorter sidewalls....

    Bigger wheels would mean shorter sidewalls. Translates to less cushioning.

    Not judging, just something to consider.
  8. There's an accessory bus panel at the bow. You...

    There's an accessory bus panel at the bow. You can get to it by removing the bow panel. Then you'll have to determine which connections are wired to what Acc switch.
  9. Replies
    9
    Views
    454

    Wherever you buy from, be aware of the...

    Wherever you buy from, be aware of the compression force on the units you look at. You don't want 130lbs force on a boat hatch. Too much force and the mounting screws will work loose after a while...
  10. Thread: Ranger Z520-C

    by Rudeman
    Replies
    25
    Views
    1,985

    Hey Howard, I have the flat cover on my 2013...

    Hey Howard,

    I have the flat cover on my 2013 Z520c. I swapped.the Fortrex out for an Ultrex. I'm able to fit the cover if I turn the control head on the Ultrex inboard. Tight but it fits.
    ...
  11. Replies
    13
    Views
    487

    I think the key is to be sure to fully coat the...

    I think the key is to be sure to fully coat the entire mating surface with adhesive. Don't allow any movement/shifting...
  12. Replies
    13
    Views
    487

    I used contact cement. Coated both sides, let it...

    I used contact cement. Coated both sides, let it dry. Then applied the pad, pulled off and reapplied it right away. It's on, very solidly. I don't think it's going anywhere for a long time.
  13. Replies
    7
    Views
    276

    I've had similar issues as well..set up is nearly...

    I've had similar issues as well..set up is nearly identical.
  14. Replies
    10
    Views
    822

    No reason to think that quality will suffer. BPS...

    No reason to think that quality will suffer. BPS brought Nitro a long way from where it started. Every line they've taken on has gotten better. Just have to wait and see.
  15. Thread: Flow rite kit

    by Rudeman
    Replies
    1
    Views
    133

    Ranger uses standard Flow-Rite components. I...

    Ranger uses standard Flow-Rite components. I replaced the livewell valves in my 94 361V in 2009. After you figure out which valves and fittings you'll need all you have to do is be sure to cut the...
  16. Replies
    3
    Views
    214

    That's what mine is set to and it works.

    That's what mine is set to and it works.
  17. Bought this one from Amazon... ...

    Bought this one from Amazon...

    https://i.postimg.cc/bNFNNHSV/shaq3-36cec86316d973dd4c60132b74e698b399ba24be.jpg
    ...
  18. Replies
    9
    Views
    284

    When I hooked up my 2019 Ford to my trailer I got...

    When I hooked up my 2019 Ford to my trailer I got a similar warning. The truck side tested good. I looked at the trailer. The light was new. I replaced the connector with a Reese Towpower 85360....
  19. Replies
    22
    Views
    696

    Comanche trim level had glass fenders. The XT...

    Comanche trim level had glass fenders. The XT series had steel.
  20. Replies
    7
    Views
    384

    I had one of these. Bought it in 1998. Used it on...

    I had one of these. Bought it in 1998. Used it on my first boat for 7 years. I transferred it to my 361V as a starting battery charger. Ran it for 13 years. I sold the 361V in 2018. I'm in touch with...
  21. Replies
    9
    Views
    420

    I went with a 6.7L. It's just easier...

    I went with a 6.7L. It's just easier...
  22. Sticky: My 2014 GT ...

    My 2014 GT

    https://i.postimg.cc/Zn2Q4nDt/GT-Driver-Side-Front.jpg

    My 1979 Suzuki GS1000EN

    https://i.postimg.cc/dt40JYJH/GS1000-EN-Left.jpg
  23. Thread: Ranger Z520-C

    by Rudeman
    Replies
    25
    Views
    1,985

    Fortunate to have one myself. They're big but...

    Fortunate to have one myself. They're big but they handle pretty easily.
  24. Replies
    21
    Views
    710

    Mine is mounted on the rear corner gunnel just...

    Mine is mounted on the rear corner gunnel just above the transducer. Console Unit uses the Point 1 for position and the bow unit uses its internal GPS for position. Both units use the Point 1 for...
  25. Replies
    18
    Views
    700

    My Z520c had already had a Precision SONAR bow...

    My Z520c had already had a Precision SONAR bow mount replacement plate on it when I bought it. The console unit was flush mounted and I couldn't see the bottom of the screen. I went with the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4