X PRESS OR G 3 IN A 17 FOOT BOAT
I am downsizing for retirement and looking at the G3 1610 or the 17 foot X press. I fish mostly small lakes and would likely not be in more than about a one foot...
Type: Posts; User: georgestarrett2
X PRESS OR G 3 IN A 17 FOOT BOAT
I am downsizing for retirement and looking at the G3 1610 or the 17 foot X press. I fish mostly small lakes and would likely not be in more than about a one foot...
I am downsizing for retirement and looking at the G3 1610 or the 17 foot X press. I fish mostly small lakes and would likely not be in more than about a one foot chop most of the time. Usually two...
I can't use a jack plate and still fit it in my garage.
I appreciate it. I will look on the boards for one.
I have a 2007 Ranger 178 vs, new to me. It has a Yamaha 150 V max with an M 23 prop. The prop is about 4 inches below the pad. At full speed it turns 5000 rpm and runs 51 GPS but there is very little...
I would like to, but my garage is small and I think I broke the trim pushing it in to the back wall as the motor barely fits through an opening to a storage room. If I had a jackplate it wouldn't...
The boat is a 2007 178 VS. I believe it is stock as it appears to be very clean. I was not sure if I could remove the oil tank or just loosen it and tilt it out of the way. I will try again this...
I was getting the boat ready for a new trolling motor upgrade from 12-24 volts. Took the batteries out, checked the water, added distilled water and charged to a full charge.
But--The Cranking...
Thanks Guys I ordered a new piece from Ranger this morning. It is going to the dealer next week for some rigging so I will let them do it in a heated shop.
I have a 2007 Ranger 178 VS. There is a plastic trim that goes across the transom under the motor mount to the edge of each side. This looks like it is one piecte. Can anyone tell me how to remove...
I have had a set of wet okole in my Tacoma for fout years. They have two tears from my dog.
The color did fade.
They have held up well and are waterproof
Do hair sticks to them like it is glued...
Thanks for the input. I appreciate it
How about from the bow to the console?
Can anyone tell me how to run wiring from the front panel to a n extra battery in the rear area. I would like to run electronics, and LEds off of a spare battery but not sure how to get the wiring...
I will try that when the ice is gone.
The center of the prop is four inches below the pad.
Thanks for the input-I appreciate it.
Purchased a 2007 178 vs. It has a Yamaha 150 V Max.
The only marking on the prop is M23- the local dealer says M is the prop family and 23 is the pitch,
I can run about 54 MPH GPS with...
I have my Dad's old Ted WIlliams reel from Sears with a matching lightweight casting rod. Can anyone tell me where I might go to find the value of this combo. I also have the original leather rod...
Are you able to alter the XI3 /XI5 foot pedal to install and LED to indicate the pedal is on ?
My issue is the lack of an LED on the foot pedal to indicate it is on. A lot of older guys can't hear the high frequency audible tone. I e-mailed the company and would love to try a new prototype.
I have had the same experience. I called Monday morning. Had a new pedal yesterday. It still will not sync. I cleared the memory, followed the directions. Remote FOB works well, but cannot get the...
Thanks. I appreciate the input.
I recently purchased a new to me Ranger 178 V. I am in the process of selecting electronics for the console.
I was told by the electronics salesman in a store that I usually trust that they often...
Purchased the Attwood T1200. Hose is way bigger in diameter than I thought but I guess I will have to make it work as it's to late to return. Appreciate your feedback, thanks.