All of those fish were released alive and well.
Type: Posts; User: jtomlin
All of those fish were released alive and well.
Pickwick Landing State Park. Didn't go far and my trolling motor quit at 9, so I just idle around.
Caught these in our club tournament this past weekend on Pickwick. 26.44 lbs with a 9.77 lb big fish.
26.44 lbs with a 9.77 lb big fish.
How long does it take to install and where would I have to bring it to for the installation?
I'm looking for a used 2003 200hp Optimax mid-section. My brother-in-laws cracked over the weekend and the dealer quoted him $1,800 just for the part, seemed expensive to me. Anybody have one or no...
You have a IM.
Dates: October 2 & 3
Lake: Wheeler
Ramp: Ingalls Harbor
City & State: Decatur, Alabama
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by BMCD »</TD></TR><TR><TD CLASS="quote">Chuck Same thing happened to me this weekend, go to the...
Mine was not tight with the old carpet and they are a little tight with the new, but I like how it is. If you go with the 24 oz carpet from Basscat, you can always take a pair of trimmers and thin...
http://www.bassboatcentral.com/smileys/praying.gif http://www.bassboatcentral.com/smileys/praying.gif http://www.bassboatcentral.com/smileys/praying.gif ...
I used a skill saw with a carbide tip blade. It gives you a very straight cut and smooth edges. The skill saw actually cut to just the right depth for the recess box. I had to take a saw-jaw and...
http://im1.shutterfly.com/media/47b9df26b3127ccec65a19b2bc0100000040O00NYuXDRsxB7efAQ/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/
A friend of mine is at Guntersville today and caught these two at...
She still reminds me from time to time on all the hard work she put into the boat carpet.
Yes, I wished I would have done the hole entire boat. I only did the very front of the front deck and the first compartment lid. I glued the pad down and then glued the carpet to the pad. Not a...
You can remove the seats without taking the panel out. It depends on the model boat, as to how the seats are attached. They all will have screws under the seat bottom on the ledge closest to the...
Nice day of fishing looks like. http://www.bassboatcentral.com/boardstuff2/beers.gif
Don, haven't gotten it to the dealer yet, so no news. You have a IM.
Thanks, I guess I will see if I can get it into the mechanic in the next week or so.
I also forgot to say that the power on the holeshot is down also. I can't hardly get the RPM's above 2500 and used to could get it 3500. I also do run quicklen/seafoam and I pulled the spark plugs...
Guys, about a month ago or so I had the compressor replaced on my engine due to failure. It quit during a high speed run, but I don't know how long it continued to run after the compressor failed. ...
Ya'll don't be getting in no hurry for Guntersville, cause I'm going to be taking all your money. http://www.bassboatcentral.com/smileys/Laugh.gif Seriously though, do consider the gas stations not...
Yes, I started with the front and worked back. I didn't trim the carpet around the edges of the lids, it only took a couple of times to loosing them up.
Don,
I should have a copy of the MSDS sheets in a couple of days. I can shot you a electronic copy of them if you would like.
I'm running just a T&H manual 10" plate and I have the motor in the very bottom holes and the plate almost at the top, I could prolly go another 1" up. The link below should give you the idea of...