Yes. Remove cartridge, put 2-3 wraps right over the o-ring and cartridge, then re-install the cartridge. Seems to be holding up very well for me, hope it works for you.
Type: Posts; User: terribleTED
Yes. Remove cartridge, put 2-3 wraps right over the o-ring and cartridge, then re-install the cartridge. Seems to be holding up very well for me, hope it works for you.
Had the same issue with mine. fill pumps as well as recirc pumps. Assuming they are the same pumps as yours (red in color). A couple wraps with teflon tape over the o-rings seems to have solved the...
Been wanting to do this to mine ever since the first time I tried using the touchpad with wet fingers. Are the red cylindrical parts in the 4th pic timers for the live well pumps?
I had one of those batteries fail in less than 1 year. Apparently lost its reserve capacity, had to jump start myself halfway through a day of fishing. Tested fine with my little 130Amp load tester...
I was using the NOCO gen 3, have since switched to the NOCO gen pro 3. The gen pro does seem to charge the AGM to a higher voltage before switching to maintenance mode.
Replaced my Interstate AGM (about 16 months old) with an X2 after getting low voltage warnings on startup. X2 lasted 7 months before it failed. Hoping my second X2 will last a little longer...
Correct me if I'm wrong, but as far as I can tell, the only function of the ecm other than housing the relays or transistors that activate the pumps, lights, horn is the timing circuits for the...
Couldn't agree more! If someone would produce a switch mounting plate that doesn't look like crap, the rest would be relatively easy and far more trustworthy.
Mine moved a bit too. I don't think the U- bolts were adequately torqued from the factory.
I simply loosen the three screws, remove the M360 unit from the trolling motor and stick it in a rod locker if I travel with the cover on. Seemed like the simplest solution for me. I do drape a towel...
I also get a puff of smoke on startup every once in a while. I think I read somewhere in the merc 4s forum that if you leave the motor trimmed all the way down that some oil can accumulate in the...
I have a '21 Z19 Pro. 80# Ultrex works fine for me. Don't have a hydro jack plate, couldn't say what difference it would make. Came with padded front deck. Top speed with tourny load is 66MPH. Played...
I don't think its adjustable. I wish it was because at full trim, mine only reads 1/4 on the gauge. The gauge is also very slow to respond when adjusting trim. Pretty sure they are all this way. ...
My experience has been very similar to Pat, just not quite getting the same speed. I do keep the boat packed with tackle, and generally over half a tank of fuel. Im pretty much maxed out @ 65-66mph....
Its not just you. I was quite disappointed to find my center storage just slightly too narrow to put 3700 boxes horizontally. Just seems dumb to build it that way.
Gonna have to get one of these!
If you are referring to the puck that says minkota on it, that is not a gps puck, it is a heading sensor for the ultrex. Nothing to do with gps.
Congrats on the new boat! I still remember the excitement the first time I started mine (giant erection) here are some things I found out...
Boat seems fairly sensitive to weight distribution, I try...
My '21 Z19 came with a 23P Fury. Runs right around 5800 rpm @65 MPH seal level.
The caps on mine ('21 model) say dexter vortex right on them and still broke. I read somewhere that they are supposed to be hand tightened.
Seems to be a characteristic of this boat. Mine is the same...
I would love to add live imaging to my rig, but there is no way I would give up my mega 360 for it...
I was not aware that these trailers are equipped with an electric reverse lockout system... I'll have to take a look tonight.
Not normal. Shame on your dealer for telling you it is...
When I got my boat (same as yours), the hot foot was setup for about a four foot tall driver. I'm over 6' so needless to say I moved my hot foot forward quite a bit. Didn't cause any problems, but I...