Thanks, I don't think it's actually leaking because there's no grease splatter anywhere and the wheels and hub are generally clean. There's just enough grease residue coming out of the caps to make...
Type: Posts; User: Shawn200m
Thanks, I don't think it's actually leaking because there's no grease splatter anywhere and the wheels and hub are generally clean. There's just enough grease residue coming out of the caps to make...
I have a 2021 Boatmate tandem trailer with vaults. I've already had to have one replaced under warranty for a rear seal leak. Now on 2 of the 4 hubs, the black indicator on the caps is no longer...
SN: 3B040833
I have a V8 200 Pro XS on a 189 Tyee GL propped with a 17P Enertia. I'm currently getting 5900 RPM at WOT (from Vesselview) and around 52 MPH. The hole shot is fine, but I've never...
I noticed this on mine when I checked it today, it looked like the bolt has backed out but when I tried to tighten it I found it was tight. It does not seat tight to the ram as Don mentioned. I went...
At the RPMS you listed mine has basically the exact same water pressure. Once you hit 5900-6200 RPM my guess is you'll be seeing around 20, that's where mine is at WOT. Temps look normal.
Update to this, took the trailer in yesterday for the warranty repair and they found that Boatmate had forgotten to install the spindle sleeve on that hub, which is why the grease was leaking. I’m...
Thanks for the replies. I’ll be taking it in to the dealer to get replaced next week. Not impressed with the vault system so far. I went 18 years with the old standard set up with zero issues and...
This is on a 2021 Boatmate trailer. Just got back from a 1200 mile tow and noticed a coating of the hybrid oil behind one of my hubs. The other 3 are completely clean. My manual says some rear...
Thanks Don, no analog gauge on my boat.
I was having the same issue with mine, so I attached it to the Starboard side of the plastic cover that is on the back of the engine. You have to be careful not to snag it when taking the cowling on...
3B040833
200 ProXS 4 Stroke
I have VesselView mobile on this engine, and would like to see the water pressure on the readout. My boat does not have an analog gauge, so I'm only interested in...
Took the boat out tonight, 90 degrees at the ramp. I did the key sequence that Don suggested and she fired off like normal with no sputter. Does that sequence allow for the vapor pocket to be purged...
It was not occurring in cooler weather, but I just took delivery in May, so it’s tough to correlate any real change in weather because I haven’t had it in any real cool temps below 60 degrees or so. ...
Thanks Don. If it were voltage or the idle relief tube, is there any reason that it would only show up on the first start of the day? Every other start, even after sitting for a couple hours are...
3B040833
Recently on startup, my motor has been hesitating a little on the initial start up. I got a video of it tonight which I’ll post below. It runs fine and subsequent starts are normal. ...
Sounds good, thanks Don!
SN: 3B040833 200 ProXS
Don, I know I’ve read on here that you strongly recommend a 20 hr service to be done on these engines. I currently have 14 hours on mine with no issues so far, and have a...
Thanks Don. I do have an account and am signed in with good internet access. Everything works and all of my normal data is being reported in real time, just not the performance data and charts. Not a...
SN: 3B040833 200 Proxs.
I have VesselView mobile on this engine, and at first I was getting performance reports with fuel consumption, speed performance charts etc. Now when I try to view these...
Just got a Lund 189 Tyee GL and I love everything about it except for the rod storage issue. The actual rod box only holds 6'6" rods and the floor storage can get 7' rods into it, but there's no...
I have the same issue on my new 200 ProXs with analog gauges. I confirmed the pickup wasn’t plugged also. I usually use my Humminbird for speed so it’s not a huge deal, but it’d be nice to have the...
Typically the warranty starts when you take possession from the dealer. At least that’s how it’s been with my last two, including the one I just picked up on Saturday.
451529
Thanks guys, I'll probably run the Enertia for awhile and look into the Bravo LT. Considering my WOT RPM's with the 17P Enertia, should I assume that the 19P Bravo would be the correct pitch for...
2021 200 Pro XS 3B040833.
Just got done with break in on my Tyee 189 GL with 200 pro xs. I ran it at WOT for a few minutes after I got through the first two hours and hit 52.1 mph at 5820 RPM...
Wanted to update this. I found an old Vengeance 18p SS prop in the garage from an old boat and decided to swap out the spitfire 17p that I'd been running and it is a night and day difference. I can...