Should be some part numbers on the one you have now. Google them. They are not used just for Ranger Boats.
Type: Posts; User: wmitch2
Should be some part numbers on the one you have now. Google them. They are not used just for Ranger Boats.
Go to an Upholstery supply and get this. Spray both sides, let it get 'Sticky' then press it down.
PM sent
You charger has a set of leads that charges 36v and one that chargers 12v both off the same charger ??
I had/have one and was not impressed. It did ok thru sparse weeds and grass, but didn't work well in heavier weeds. I've heard some guys put 2 on and it works much better. i don't fish weeded...
New, gray, no red !!!
https://www.westernbass.com/forum/z520r-fold-down-pedestal-seats-t146657.html?sid=c50fb5e01d3060e22ed44cf7abc873b2
I went with the Fulton F-2 clamp on and used a mounting block with it. Best and easiest jack ever !!!
Be sure to use ALUMINUM Rivets too. If you ever have to replace one, they're easy to drill out.
This is the best stuff I've found. Been using it for years !! On Amazon !!
Remove the lid from the boat. Drill out the existing rivet heads and punch the remaining part into the lid. Drill the hinge and lid with a 1/4" drill and then install the hinge using 1/4" x 1/2"...
That depends on what you want to put back on. If you want a sleeve like is on there now, you have to disconnect ALL the wires and feed them thru the new sleeve. I cut the whole sleeve off, (using a...
Could be, check the fluid level, fill if necessary, and try again !
Top off the Master Cylinder and have someone pump the brake, like bleeding them, while you are under the trailer with a flashlight and look for the leak.
Well, I’ll be Damned !! Just got an email from them saying my shipment is on the way !!!
Not sure on the Ghost, but it's always been advised to disconnect the Trolling Motor when charging the Batteries. Either unplugging or using a switch or breaker to disconnect, that way if an...
20 some years ago, I had a partner that we fished 2 different Team Circuits. We switched off using each other boat. The way we worked it, Fill the tanks on both truck and boat before the tournament...
Go to a Pool Supply store and get the O-Ring Grease for on the Filter O-Ring. I lube mine every 5-6 Months. Stays on !!
A 220 outlet should be a different configuration. I'd check the outlet with a volt meter to see tho. Let the chargers rest for an hour of two, then try them in a different outlet that you know is...
Is it in the stowed position or the deployed position ? Mounted or just on the ground ? You may have to push DOWN on the mount and then pull on the cord.
Unfortunately this is what I'm finding out !! I thought they were a reliable company !
Try using 2 3/8's oz A-Rigs hooked together end to end for a bigger profile and added weight to take it down deeper and keep it there.
I've fished Shasta many times and use a Tex-posed 6" Roboworm Morning Dawn on a #2.0 EWG with 12# Fluro leader. You just have to Finess it thru the trees, but need the 12# to drag them out !! Love...
I use a Shin knot for Braid to Fluro Leader and cut it to be twice the rod length. Then re-tie when the Knot is just outside of the tip.
Level the trailer unhooked, then measure from ground to the top of the hitch. Whatever that measurement is, that's what you want the top of the ball on the tow vehicle to be. Depending on your...
C & E Boat Restorations, England, Arkansas 870 575-3948 Curtis Massey He does AMAZING work !! I live in Fresno, Ca and when I get to where I need new carpet, I'm gonna drag it from Ca to...