Team C&O, I have a 1990 Hydrasports dual consol (DV-TSX). The windshields are somewhat squareish with sharp angles where they wrap around. I'd like to give the boat a more modern look with smoother...
Type: Posts; User: frankfish
Team C&O, I have a 1990 Hydrasports dual consol (DV-TSX). The windshields are somewhat squareish with sharp angles where they wrap around. I'd like to give the boat a more modern look with smoother...
Thanks for the info swamprat but my windshields are original and definately not smoke color. Wish I could post a pic, but everytime I try, it fails to upload. There is a pic in the Hydrasport boat...
I will take some measurements GoFastBoater. Do you have both windshields or just one? Would you mind sharing a Facebook name if you have one? I'd like to coorespond through Messenger, as I don't...
I've had my 1990 Hydrasport DV-TSX for two seasons now, and its a great ride. Not all that important, but I'm curious. The insides of my smaller storage compartments are yellowish to off white. ...
I have a 2015 Ranger 118C and some of the push button switches on the dash and bow stick shut? The boat has been stored in a heated garage the past two winters. Has anyone else had this problem? I...
That's about what I'm looking to spend $200ish. Thanks I'll check out Aurora!
Mashfan, Thats about what I was quoted for a custom made cover. I just can't swing that much now. Still have to have my lower unit seals replaced, and looking to upgrade my electronics. It sure...
Still learnin, by chance, do you know what make it was and model? Thx.
Can anyone provide me with a link to a pre-made boat cover that would fit my 1990 DVTSX Hydrasport (dual console)? I priced out a couple of local canvas guys to make me one, but $$$Ouch!
I'm good The toothpick trick worked. Carbs cleaned Thanks guys.
That may very well be 316jughead. I'm going to try it again. Will screwing it tighter unstick the valve seat or should I maybe try manually depressing it with some type of tool or something?
Thanks for the response, but I'm making a mess. My maintenance valve is the same as the pic Fred provided. I started the motor, screwed the spray can fitting onto the adapter, flipped the valve in...
I feel kinda stupid asking, but I have the adapter hose that threads into the fitting below the Primer selenoid, and purchased the Johnson decarb spray for my 1990 GT175 engine. What position should...
Thank you CastingCall, I will definately take your advise on the epoxy sealer and fiberglass cloth. I was just going to use a Spar type of sealer.
I realize your thread is aging, but did you line the inside of the extension with carpet? If so, do you have any moisture problems due to the lack of ventilation? I need to redo my deck extension...
Hi, My Hydrasport currently has what I believe is a homemade deck extension made of 5/8th plywood, and the inside walls including the divider, lid and floor are carpeted. I bought the boat this way....
Thanks ChampioNman. Good summary.
This post has me curious. Can you guys tell me what diameter the anti siphon valve ball is and possibly send a pic? I ask because back when I was trouble shooting my fuel restriction issue I found a...
Btw, I did de carb it when I first bought the boat and I bought the special fitting that screws on where the manual primer valve is but the fluid would not feed. Instead I removed the cover and...
Thanks guys. I just recently added oil to the gas. I've only gone about 6 miles total since getting the boat and didn't notice any appreciable oil drop in the reservoir tank yet. I was told that...
I have a 1990 GT-175 with a four blade prop. My VRO is still intact, but I also recently added a 100:1 oil mix to the gas (XD-50 oil). The engine is still new to me and it being an older engine, I...
I still have my VRO connected on my 1990 GT-175, but from what I read, if you remove the VRO, you also need to unplug the sensor. Maybe you didn't do this?
I recently had alarm issues in my 1990 GT 175. I unplugged the tan wire sensors going into the powerhead but that didn't shut the alarm off. When I unplugged the one for the vacuum switch, it shut...
I was afraid of that. Ugg
I had a bearing buddy fall out of my Ranger Trailer hub (1995 trailer), and in the process the grease spun out and eventually disintegrated the bearings. It was a miracle I made it home in the...