Got mine from K&K Kustomz. He was very helpful and got to me as soon as possible. Would highly recommend you checking with them.
Type: Posts; User: Red70
Got mine from K&K Kustomz. He was very helpful and got to me as soon as possible. Would highly recommend you checking with them.
Well the saga continues. Dealer received a new sensor so I took my tester and volt meter and tested new one on the parts counter. Guess what, it reads 4.75 volts at rest and does not change when...
Hey Leon. I found an old tpi from about a 94-95 200. I tested it with 5 volts and grd on bench and it shows 0-5v when rotated. I reversed 5v and grd and sensor shows 5v at rest and 0 when rotated. I...
Here are readings from both TPI connectors disconnected. (A=GRD B=sensor return C=5 volt )
TPI 2
A-B 4.75v
A-C 4.98v
B-C 0 v
TPI 1
A-B 0 v
A-C 4.98v
Got a new sensor and didnt fix problem. Only thing I can assume is maybe the ECU.
Thanks Leon, that is exactly what I was looking for. I get no voltage change on sensor output wire on TPI1. TPI2 varies voltage on sensor output wire as supposed to. I can plug sensor 1 connector...
The connector terminals have good tension on them at the sensor and ecu, not pushed out,spread or corroded. Connected to original and does same thing. I come from the auto repair profession so yes I...
I had a similar issue. My anchor lock would immediately push boat about 15 feet backwards and hold there. I was hopeing a software update might correct it so I updated graphs with active captain and...
Yes. #1 stays at 5 volts and never moves. You can unplug sensor and it goes to 0. #2 is at 0 and ramps to 5 volts when throttle moved to wide open
Yes I keep thinking that but it is doing exactly same thing as old one. When I check voltage at TPI connectors(disconnected) # 2 has 5 volts on 2 terminals and GRD on other terminal. #1 has 5 volts...
1998 Mariner 150 OPTI #0G655960. Last June was getting alarm and no power. Connected to MEDS diagnostics and showed TPI codes about 90 times each. Both would sweep but while idling, the #2 TPI would...
Force will not connect to Active Captain or a graph. My phone does see trolling motor wifi but thats as far as I get. Garmin had me reboot everything and even tried 2 other phones but since neither...
Thanks everyone. Will look at all suggestions. I do have a Trophy Plus 24 4 blade with the exhaust ring I am going to try first. Will update when know more
1997 20ft Jaguar. 225 Mariner 25 Trophy Plus 4 blade. Power Lift Manual Jackplate. Boat has terrible holeshot, when finally gets on plane it runs great. What is proper prop to pad setting and best...
Maybe its just me but I seem to have noticed a lot more steering arm swivel to lower splined yoke wear with the short motor braces than when using the trailer supported ones. I went to one of the...
Received unit back from repair and have had out a couple of times now. It seems to be much better, close to, if not as good as before. They said they did a circuit board repair? Maybe was a...
I talked with Humminbird again today and they were very nice and seemed like they wanted to try to correct issue. I sent unit in today and will let you know what happens.
Ok so I removed all waypoints and restored defaults as Humminbird suggested and image is still not sharp and crisp as before update so dont know what I am going to do now. I was in the market for a...
CRAWFW you are right about not bring able to go back in software. In my opinion that is not good engineering on their part. There should always be a backup for updates because there are usually issues
Thanks for all the info, Humminbird advised me to export all waypoints onto a sd card and then remove from unit, then format nav directories to the unit, check the views, if not better to send in for...
Thanks for info Tyler82284, PlanoKeith did they give you an estimate on cost of motherboard replacement? Just trying to decide whether to repair or replace
I dont know what version it had before I updated. I purchased in Feb of 2018 and this was first time to update.Big mistake. I have tried switching to all available transducers listed as well as...
I have a Helix 12 Chirp SI DI GPS G2N. SI has always been sharp and clear until I performed the update 2.280. Now it is fuzzy and not clear even after restoring to defaults. In simulation mode it is...
Check for DTC's. If a code is setting but not turning on check engine light it will cause fuel filter service message when it actually does not need replacing
That is a check valve that permits oil to enter the VST but prevent gas from entering the oiling system. Best to remove and install a metal plug. Don't remember the thread size right now but should...