Nice rig brother :thumb up2:
Type: Posts; User: jmahaney
Nice rig brother :thumb up2:
I have moved the prop shaft up to 1/2 inch below the pad and now the WOT water pressure is between 10 and 12 so I won't go any higher, but I am now hitting 76 fully loaded! (gas gauge even reading...
No it was closer to 2 feet than 6 inches. 45km west winds on a lake that runs east to west, pretty decent white caps Lol But i think we’re missing the point here one thing I’ve noticed with my rig...
To be honest, they may not have been 2 footers where i was running open but it was still stupid rough. Trim down a little and hammer it the 21XD handles some dirty water. It's really not that hard...
I dunno man it was rough, rough enough i wasn't holding it. :laugh:
So went out today about 1/4 inch higher on the jackplate, the absolute highest i can go now before going down a hole on the motor. It was super windy so it was hard to punch it for long but I...
Sounds good, I will be installing the gauge today. I blew out the lines last night cleared all the gunk, but the gauge itself was definitely no good. I'll make the swap and see how it goes. I am...
Fair enough, the feedback is already appreciated. I’ll have to make the best guess at a second prop and hope for the best, I’ll install a water psi gauge here too and get the motor up some
more....
Yeah I don’t know what to tell ya but the poles changed it about 1mph, didn’t affect hole shot at all. They are only 8 footers and ported holes to lighten the poles, I was fully aware expecting to go...
Right, the motor can spin 6000 no problem. 5800 being ideal. The power poles believe it or not didn't slow the boat down noticeably at all. Probably went from 74 to 73 and change. The poles...
When I read the manufacturer recommendations on the Bravo XS they say to go up 2 pitches to replace the Bravo 1 which is currently on the boat, would I not in theory gain rpms going up to a 29...
Fair enough, from what ive read the bravo xs turns higher rpm than the comparable bravo 1 so that's an interesting option for sure
Thanks for the reply, I'll get working on the water gauge right away. I am told 5800 rpm is the sweet spot on this engine but I believe the limiter is 6200. I would definitely be more than happy...
Hey guys, I've been lurking the bullet forums since I bought my 21XD last spring. I have been super happy with the ride, very dry and a great rough water boat. I have run Tritons, skeeters,...
right now im leaning towards the 24 raker 2 .. but if any fellow g2 owners experience to share im all ears
Hello,
I have a Trition TR 186 that was running 62 mph (gps) with a Mercury 150 optimax (long shaft) .. unfortunately it needed a rebuild so I decided to repower with a new 150 H.O G2. The old...
yeah exactly.. so it's not in the way. I haven't had a chance to look at the motor yet, ill take your advice and remove the bow gaurd and make sure the pin is pressed all the way down so the lock...
The rope doesn't seem to be in the way at all. I'll remove the bow guard this weekend and see if I can figure out what's happening. Thanks for the response guys!
I also found that the walmart everstarts are absolutely great! beats any other battery i have used.
Yes at one point the bow guard was taken off. I guess I don't know what the properly installed safety lock should look like to tell you what position it needs to be in, but on second thought if I...
that's exactly the piece that seems to be sticking. I don't recall taking anything apart that didn't require coming apart. The mount latched fine when i replaced the rope for a while after, this...
Hey Everyone,
I am having trouble with my Fortrex mount, at some point last year I replaced the rope and shortly after I was having trouble getting the trolling motor to lock properly in the...