Search:

Type: Posts; User: Invader186S

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    81

    I just listed one in the props fro sale section.

    I just listed one in the props fro sale section.
  2. Replies
    14
    Views
    476

    Thanks, I'm sure this will help others as well. ...

    Thanks, I'm sure this will help others as well.

    For what ever reason, my engine doesn't have the S and W connectors. I ended up using a Lowrance pressure sensor and plugged it into my NMEA...
  3. My 3.3 HPDI does this occasionally just as you...

    My 3.3 HPDI does this occasionally just as you described. Not when cold, but after it has been run, it can be hard to start. I can always get it restarted by giving it a lot of throttle in neutral....
  4. Replies
    1
    Views
    328

    Still for sale. Price lowered to $500.

    Still for sale. Price lowered to $500.
  5. Replies
    6
    Views
    418

    I know you said all plugs were firing but I would...

    I know you said all plugs were firing but I would check the resistance of the sparkplug boots. They are spec'ed for something like 5K-7K ohms. They simply unscrew from the wires. Remove each one and...
  6. Replies
    3
    Views
    228

    Thanks, I'll check there. Did you notice if...

    Thanks, I'll check there.

    Did you notice if your engine was any quieter with the cover on? My engine has the Hydro Tec Phase III mods. There is no insulation under my hood, the throttle bodies...
  7. Read this. Everything you need to know. I've...

    Read this. Everything you need to know. I've referred to it many times. It is in the how to listing.

    http://www.bbcboards.net/showthread.php?t=32749
  8. Replies
    3
    Views
    228

    Source for 3.3 HPDI Verted Hood Cover

    I'm looking for a vented hood cover for a 3.3L HPDI that can be used while the engine is running. RMP use to listed them without the Yamaha graphics but it looks like all Yamaha covers have all been...
  9. Replies
    14
    Views
    476

    Tx Champ THANKS!, Can you trace the wires back...

    Tx Champ THANKS!, Can you trace the wires back for the W connector. Do they just disappear into the main wiring harness or do they go somewhere else?

    I'm not the original owner of the motor so...
  10. Replies
    14
    Views
    476

    Ok, I have my engine RPM, trim, temp, and voltage...

    Ok, I have my engine RPM, trim, temp, and voltage displayed on my Lowrance using the ECU to NMEA connections. I still can't find my W connector to add water pressure to the ECU.

    If anyone has...
  11. Replies
    1
    Views
    397

    The 25" is sold, 26" is still available.

    The 25" is sold, 26" is still available.
  12. Replies
    1
    Views
    397

    25" and 26" Trophy Plus

    25" Trophy Plus. Useable but on the rough side. Good prop for the shallows. Leading edges are rough, the tips and trailing edges are not bad. Blades faces have scratches. $200

    26" Trophy plus...
  13. Replies
    0
    Views
    253

    Small Hub Props with Flared Barrel

    I've had 2 different fish/ski style boats that I have tried many different props on. Quite a few years ago I found that a Mach IV prop was by far the best prop for hole shot and top speed. This prop...
  14. Replies
    1
    Views
    328

    Mazco 26" RE4

    Mazco 26" RE4. Weld-in fat shaft hub. Great shape but not quite perfect. Has a few minor imperfections that don't quite show up in the pics. Close inspection will show a few minute nicks, scratches...
  15. Replies
    14
    Views
    476

    White

    White
  16. Replies
    14
    Views
    476

    Thanks. I see the water pressure connector is...

    Thanks. I see the water pressure connector is marked "W" not "P".
    Anyway, my question was..... I can't find the S and W connectors anywhere. But I do have a NMEA connector. Could some early NMEA...
  17. Replies
    14
    Views
    476

    NMEA 2000 Water pressure on HPDI

    I have a 2006 3.3L HPDI. I'll be adding a water pressure gauge to the display. My engine has the white NMEA connector on the right side. There are also suppose to be two electrical connectors on the...
  18. I think it was a little less than $4K with 6 new...

    I think it was a little less than $4K with 6 new pistons, one hole sleeved, the others bored, bearings, a check of the fuel and ignition systems, gaskets to reinstall the powerhead, one year...
  19. I broke a piston on my 2006 3.3L HPDI several...

    I broke a piston on my 2006 3.3L HPDI several years ago. I sent the fully dressed powerhead to HydroTec by freight. They rebuilt it and shipped it back. Everything went smoothly. Still running great.
  20. Update...I found the white NMEA interface...

    Update...I found the white NMEA interface connector on the right side of the engine. But I can't find the speed and water pressure 3-wire connectors anywhere. From yam911, they are suppose to be on...
  21. Replies
    5
    Views
    236

    The Signature Eagle 4 and Merc Pro ET look very...

    The Signature Eagle 4 and Merc Pro ET look very similar. The pics show a 15x24 Eagle 4 on the left with a 14-5/8x 26 Pro ET on the right. The Eagle has thinner blades. I believe the Eagle is also...
  22. Replies
    13
    Views
    885

    For water sports, I've found a Bravo with the...

    For water sports, I've found a Bravo with the full flare barrel works the best. On my setup it provides the best low speed planning for knee boarding and wake boarding. 8 PVS holes will probably be...
  23. Replies
    9
    Views
    574

    In addition to the above recommendations, make...

    In addition to the above recommendations, make sure your boat is balanced side-to-side. I carry a level and check it every time I launch so I can move things around before taking off. On my setup,...
  24. Yes, I had the same problem. I could not get the...

    Yes, I had the same problem. I could not get the top cap to seal. I've seen posts that mentioned the plastic assemble can warp over time and often needs replacement.

    I was also having problems...
  25. I'll have to check that side of the engine for...

    I'll have to check that side of the engine for the connector when the weather warms up. Again, thanks for the quick responses.
Results 1 to 25 of 198
Page 1 of 8 1 2 3 4