Search:

Thanks for the info.
Well i will agree that they are auto sensing. the cables i made are straight through, i did not follow the instruction LOL.
thanlks

Good evening,

I bought the connectors from garmin to make my own ethernet cables. My question is do they need to be wired as crossover or straight through?

thanks
jim cav

thanks guys

I will load test each battery. One thing I left out is if i am running at 100 % it will kick in to high speed for a short time and then cut back down to 66% ruff guess with the 66%. ...

I have a fortrex 112 when running at 100 % the voltage from the batteries is 38 volts when the foot pedal is set to 100% the voltage to the motor is only 30 volts not 36 volts. I am thinking dc motor...

what did you program a plc by chance?

Good morning

Is there a written Bench test procedure I can do with a multimeter for the rectifier regulator?

Thanks

Good evening,

I have a garmin echo map 93sv this unit on the front of my 14 foot Aluminum G3. about 4 months ago the gps starting acting up. Everything will be fine and then the screen will goto a...

Good evening,

I am using the bass pro shops lockdown marine electronics mount it is a good mount for the money. Does anyone know who the manufacture is, I would like to buy additional parts.467890...

Good evening

I am posting this for a friend, thanks.

Having issues with fuel pressure. Boat will only top out at 50 when usually does mid 60. When taking off the ball is hard but after a 5...

hello

i have a 2002 yamaha vmax VX225TLR8, where is the plug for the yds yamaha software located?

Thanks

Hello

I have a 1999 ficht 175 model # E175FPLEEC, Motor with start and run for 5 sec or less. No check engine light. The following fault codes stored in ECU. 15 rom failure, 16 crank sensor and...

I ordered the manual, I will download shortly but in the mean time here are the codes I got thought the check engine light.
26, 43, 35, 37, 48, 47 Any thought?
thanks

What website would be the safest to download from ?
Thanks

Good evening

I am helping my fried he has a 1999 ficth 175 hp and the power distribution panel went bad. I was able to repair the PDP by re-soldering the connect ion on the circuit
board. The...

I ordered part # 32 it came as two pieces but only shows one piece on diagram,41115-ZW1-003https://cdn.boats.net/MTA/d/5/NjQxOTQ-5633c97c.png

Hello guys,

I have a 226-4008 that i need to test. Would any one have a wiring diagram for this part?

Thanks

Jim Cav

My hds gen 3 has a web interface. I use it to back up the unit.

Does the garmin 93sv udh have a default ip address?

thx

jim cav

good morning

i have a older minn kota 101. this motor has the older armature that has the steel ball in the end of the shaft. the armature is new not been used yet it been on the shelf for many...

I have a garmin 93sv uhd, there is the panoptics transducer for 499 or the black box and transducer. what is the difference?

Thanks

The best way to show what is going on is pictures. What causing the lines on the left.

well i am the idiot i forgot to lower the power poles before backing into the garage. I cant find a parts break down so i can order parts. I need the aluminum clam shell parts. does anyone know the...

I even rolled it back to ver 4.0 the funny thing was when I tried 7.0 the water temp would come back for a few seconds then go away. I did hard resets every time i changed the firmware. The TI2 has...

does lowrance plan on updating 18.2 for hds gen3. I have tried everything to get sonar to work again. I even call tech support too, what a joke! They want money to solve a problem they created.
...

Thanks Guys for the quick replies,

So I have done everything that was talked about and more. Here is what I found on HDS gen3 7 under system: about: Sonar version 0.0.0 On my HDS gen3 12 sonar...