Search:

Thanks guys will makeup #4 and connectors for install.

I’m installing a Ranger type jumper switch in my 2007 Ranger. Found a 4 position switch by Blue Sea but need suggestions on wire size. I have a 150 Mercury Optimax motor. What size wire is...

I’ve just installed a 126 ultra on my boat,I have two 93 sv about 2 years old. I have the network switch and Livescope. I moved one 93sv off to the side of the bow with the 126 in front of the...

Thanks again, appreciate your quick response. Will give that a try, should work out with same end result as present sit-up , but with only the three units .

Thanks Michangler, that package is pricey. I wonder as an alternative could I move the one 93s to the console , I have a 93s presently there . With the two could I run a GT 8 on one and the GT 54 to...

I presently have two 93 sv ultras and a older Helix 9 and a LSV 34 panoptics. I use the Helix for depth and mapping when I’m up on plane. I just purchased a 123sv for for the front to better...

Sent a Helix for repair on Monday before Thanksgiving. They received it on Wednesday, it was repaired and on my front porch on Friday afternoon day after Thanksgiving. Wow that is quick service.

Headed to Green River on Monday. Any fishing info would be appreciated. Have the fish moved and started the fall feed, have bait fish started to move out of the creeks. Thanks

Anyone fish Nolin this weekend? Going down middle of next week for some bass fishing

Not surprised on the redeau chain always some good fishing. While we are all vaccinated would be difficult to be tested in a timely manner and have all the plans required . Just going to fish the...

Thanks Mike it does help. 4 of us are going up on Monday will fish for 6 days . Hope we get a few nice smallmouth. Will report on what we do and how we did.

Appreciate it if you would let us know how you do.

Thanks that helps. Haven’t fished the River in a number of years. Been going just north of there to Charleston Lake and the Ridue chain. That is is not in the cards with all the restrictions this...

How about a fishing report? Did you fish the river or go out on the lake? Any pattern you could share. I’m going up the 14th of September for a week appreciate any info you can share.

Had a friend who blew a tire and put a hole in the fender of 2010 Z518. He found a local mechanic who did fiberglass work and had a repair done using Ranger matching color and metal flake for $350 ....

Years ago I had OMC trolling motors, one foot control one hand control. I would change them out before going fishing according to what and how I intended to fish . Crankbaiting used foot control soft...

Thanks Wayne will give those two things a try.

I have a Helix 9 1st generation SI unit on the dash with a splitter on a glassed in the hull transducer. The unit has shown true depth reading since installed several years now. Lately when on plane...

Thanks that reinforces what I understood to be the case. How improved is the clarity of the later generation over the original?

I presently have a 959 at the bow and Helix 10 SI Gen 1 on the console with a Ultrex with I-pilot link, all Ethernet connected. Thinking of upgrading to Helix 9 SI GN 4 for the console and moving...

Thanks just talked to Jones Trolling motor. They were very helpful and said as you just indicated. He shipped one out for me today. Appreciate your info and help.

Thanks Bill, i will give Jones a call. The shaft diameter is 1-3/4” which I think matches the Fortrex diameter. Appreciate your help.

I’ve had my Ultrex for one season and have always carried an backup trolling motor when fishing out of town. I have a 65 lbs Maxuum with a standard Maxuum Bowguard . I understand that if I replace...

Thanks that was what I kinda figured but got thrown by the wording in the written instructions.

Eithernet hub instructions say install hub on a flat level surface. Can it be installed on an upright surface? I’m thinking of the rear wall of a rod locker in front of drivers console. Thanks for...