Ok so I have tested the grey circuit with dva. Getting like 13 volts DC. Not 9. Maybe my meter is bad. The stator seems to be working getting like 13.8 at 2500 or so. None of the tests so far...
Type: Posts; User: Mike482Ranger
Ok so I have tested the grey circuit with dva. Getting like 13 volts DC. Not 9. Maybe my meter is bad. The stator seems to be working getting like 13.8 at 2500 or so. None of the tests so far...
Ok so a little more research the DVA takes AC and makes it DC? and that is where the 9v comes from?
Ok, so ill double check the red lead, however it was attached as of last night and everything worked great last weekend. Maybe dirty contact. As for voltage there is no DC voltage on grey wire? I...
Hey guys, weird one here. I recently replaced my starter and the boat ran great at last tournament. Then the other night I launch and fire it up and my tach is dead. I tested the grey wire at the...
Based on light pattern and wheel yes. The detents are now nearly center for both idle and high. Idle is back like 2 clicks but I believe I got it. Looks like most others now. Way better than my...
Jughead, I'm sorry I truly thought i did. I do think I don't have the full directions. The print out on easy timer i have (2 pages) describes TDC locate and the light on off principal reversal...
Got it. After I realized my tdc stop had some play in it. I teflon taped the inner threads and got a better tdc. After that the idle point looks way better. High speed I defaulted to light just...
Thanks Jughead. I will try again when I get home. I have 1 full page of directions and a page that describes the optical gaps. Got the easy timer from previous owner. Just to verify, I am watching...
Championman or Jughead. I noticed that I can only adjust idle timing to 6 degrees. No more clicks for 4. Could the idle timing apparatus be installed slightly off? Maybe remove and turn slightly?...
Hi guys,
So I replaced the cracked primer valve housing and gasket. Did a link and sync. The JohnnyRude Easy Timer is the bomb. I think I did it right and will test tonight. I did find that...
never mind I found it. I will do all of the above listed tasks.
Mike
I do have your directions. What is the VST tank?
Mike
Ok the gaskets are orange. They are oily damp on the outside is that leakage or just saturated gaskets?
Interetsing shovelhead98, Just no balls at hi rpm? I am having propped checked. My bowls are damp around edges but no obvious gas spraying out with primer. I did find a crack on the housing for...
J150GLERA. How do I tell late from early. Psyched boat came with easy timer and the maker is available for tech support. Lol.
I bought a Ranger 482v with a CMC jack plate Hydraulic and a 150 fast strike Model J150GLERA about a year and a half ago. Have done minor maintenance over the past year new Vro, plugs a few times,...
figured it out
Hi Guys,
So I changed over from my older HDS units to 2 Helix 10 Megas (SI/DI). I also have just received my 360 imaging ultrex setup and will be installing tomorrow night. I hate not having...
No on wires if your still wondering. They are 6 awg. Plenty for that length of run. You should have 2 spare wires too. cool for additional 12volt feed.
Mike
Hi guys. Just installed a new water pump on my 150 fast strike. After I was all done I noticed a small hole where water begins to head from impeller to engine tube. It looks deliberate like it...
Your splashwell should drain through the boat, not into your bilge that's got bad news written on it.
I did mine like scotti. Just keep 3 bolts in play at all times balance wasn't an issue I did have issues with the right side bolts and a CMC actuator interference doing the install. My bolts...
I think I own your old 482. Too funny. Still kickin, stored indoors. Recessed Troll well now. Otherwise pretty much the same. Still kisses 60 when trimmed right.