Search:

Type: Posts; User: Carolina_Rig

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    535

    And does said hunter have to sacrifice his...

    And does said hunter have to sacrifice his underwear for toilet paper since the 4 napkins in the glove box were nowhere near enough, thinking to himself the whole time "how many pairs of underwear...
  2. Replies
    1
    Views
    566

    Trolling motor foot pedal loose??

    I recently noticed one of the screws holding my foot pedal down had gotten to the point where the threads weren't holding it down anymore. My first thought was to just find a slightly larger screw. ...
  3. Replies
    15
    Views
    5,364

    In fact, on and under it

    In fact, on and under it
  4. Replies
    15
    Views
    5,364

    I'm not substituting Perfect Seal for a gasket. ...

    I'm not substituting Perfect Seal for a gasket. I would never do anything that idiotic on something as important as the cooling system on an outboard. The Mercury factory repair manual calls for...
  5. Replies
    15
    Views
    5,364

    Water pump base. 2004 Optimax 175 OT922019

    Water pump base. 2004 Optimax 175 OT922019
  6. I've been following this thread for some time to...

    I've been following this thread for some time to see how it progresses. I also have interference with the graph at the bow and I'm undergoing similar steps to resolve. Here's where I'm at. Garmin...
  7. Replies
    15
    Views
    5,364

    I went ahead and ordered the Perfect Seal as...

    I went ahead and ordered the Perfect Seal as well. I also saw threads about the Aviation Form A Gasket at various places.
    Like you said, it's cheap enough and I'm waiting on some other parts to...
  8. Replies
    15
    Views
    5,364

    I thought so too. thanks

    I thought so too. thanks
  9. Replies
    15
    Views
    5,364

    Mercury Perfect Seal question

    Is Permatex High Tack gasket sealant an acceptible substitute?

    thanks
  10. Replies
    32
    Views
    2,445

    Can you post a picture of the interference you...

    Can you post a picture of the interference you have? So you're still seeing interference when you bump the TM?
  11. Replies
    32
    Views
    2,445

    Anytime bro. Hope you get the issue resolved.

    Anytime bro. Hope you get the issue resolved.
  12. Replies
    32
    Views
    2,445

    You want to run the ground wire from the skeg to...

    You want to run the ground wire from the skeg to the ground (-) on the 36V TM power supply; not to the ground on the 12V power supply.
  13. Replies
    32
    Views
    2,445

    Yes, and they are separate. 24VDC routes up the...

    Yes, and they are separate. 24VDC routes up the passenger side and the terminal block is under the bow console panel. The Ground from the skeg is connected to the (-) on the terminal block. It is...
  14. Replies
    32
    Views
    2,445

    I'll take some tonight and post up tomorrow. (or...

    I'll take some tonight and post up tomorrow. (or later tonight)
  15. Replies
    35
    Views
    3,822

    I've given Flouro more than enough chances. I'd...

    I've given Flouro more than enough chances. I'd find myself allured by its "inivisibility", try it, get frustrated with it, then after a few years I'd forget the whole experience and do it over...
  16. Replies
    32
    Views
    2,445

    I had interference from my trolling motor. ...

    I had interference from my trolling motor. attached picture shows a couple bumps on the motor before I addressed it. I drilled a thru hole in the skeg of my maxxum and installed a #10 screw with a...
  17. Replies
    10
    Views
    643

    whew...lemme catch my breath. I read that all in...

    whew...lemme catch my breath. I read that all in one breath. Anyway, I've had to use an electric hair trimmer like someone else mentioned. Works well. Good luck
  18. Replies
    14
    Views
    1,208

    Decorative Plastic Sheets sells them. They'll...

    Decorative Plastic Sheets sells them. They'll send you samples too. I went with the ABS woodgrain plastic when I reconfigured my gauge panel, but they have carbon fiber patterns and other patterns...
  19. I've got the Trimax TH6 on my '04 185VX. It...

    I've got the Trimax TH6 on my '04 185VX. It works great. You can get them from Amazon for about $18. Just an option.
    ...
  20. Replies
    5
    Views
    2,034

    Okay I think I'm good now: 55 plate to hull / 90...

    Okay I think I'm good now: 55 plate to hull / 90 motor to plate.

    I plan to reseal the bolts going thru the hull.
  21. Replies
    5
    Views
    2,034

    I did look there, and I guess I still came away...

    I did look there, and I guess I still came away scratching my head.

    The OP was mounting a 250HP Merc to his 520. I just guessing the transom is a bit more beefed up on that one than mine. Then...
  22. Replies
    5
    Views
    2,034

    Jack Plate Torque Specs needed

    Hey guys, I'm looking for the torque specs for Jack plate to transom.
    I'm guessing motor to jack plate torque would be the same?

    2004 185VX with 175 Opti.

    Thank you,
    Dan
  23. Replies
    13
    Views
    567

    Actually, It's got a Rite-Hite on there right...

    Actually, It's got a Rite-Hite on there right now. While I don't want to create non-existent problems with the boat, I've read some absolutely terrible reviews/stories about the Rite-Hite brand... ...
  24. Replies
    13
    Views
    567

    Thanks guys. I've been eyeing that black powder...

    Thanks guys. I've been eyeing that black powder coated Vance. JPL4500
  25. Replies
    13
    Views
    567

    Need Jack Plate Recommendation

    I've owned my current Ranger for a few years and after reading some bad press about the jack plate that it was rigged with from the factory, I think I'd like to replace it.

    I'm just looking for a...
Results 1 to 25 of 27
Page 1 of 2 1 2