I have a Custom boat storage cover for Stratos 295PE. $175.00 - Contact me for details. Cover in Penn at Zip 18974. Will ship for cost.
Custom made Bass boat winter cover. Was used on my 1999...
Type: Posts; User: Newheart21
I have a Custom boat storage cover for Stratos 295PE. $175.00 - Contact me for details. Cover in Penn at Zip 18974. Will ship for cost.
Custom made Bass boat winter cover. Was used on my 1999...
Just bought the same case from Academy, on sale for 9.95. Works great, nice case.
I have hydralic steering and enough length on all my cables and hoses.
I have a 1999 Stratos 295 PE signal console with a Yamaha V-Max 150hp motor and a 23p prop and a power pole. Any recommendations for the best distance for set back on the jack plate?
The power pole...
What software version are you running on post # 9 ?
Use two coats liquid electric tape over connectors and let it dry. Do not use water base type, just solvent base liquid tape. Have been doing this for years on all my saltwater boats. never a problem.
I am installing a Yamaha 2003 VX150tlrb 2 stroke OX66 outboard on my bass boat. It came woth a 703 control box. I want to put a flush side mount control on it. Does anyone know what Yamaha flush...
I am re powering with a 2003 Yamaha Vmax 150. What size and spline prop fits these motors. I am removing a 1999 e-rude 150 and would like to know if my old prop will fit. It has been a while since...
Re powering 1999 STRATOS 295 PE with a 2003 Yamaha 150 V Max 20in shaft motor. Need starting prop size. What prop shafts fit this motor? Looking for 3 or 4 blade for good hole shop and mostly mid...
A 1999 Mercury 150 2 stroke with carbs, about 250 hours or a 1997 Merc mariner 150 2 stroke with EFI with 500 hours on it?
I am using this on small lakes with no real long runs.
Thanks, I found a 200 merc.
I have a 1999 Stratos 295 PE bass boat I have had since new. I want to replace my Evinrude 150 hp Fitch motor. I do not fish tournaments or do long runs. I mainly fish a series of small lakes. I have...
Looking for parts motor Suzuku DF200 20in shaft. Motor condition not important. Must have a good lower unit and mid section. Want to convert a 25 in shaft to a 20 in shaft. Need misc parts and good...
I have a 1999 fitch 150 with only 80 hours on it. It runs fine but I fish a club with four lakes and I idle and troll a lot. I have the DF200 on my other boat and it is like new. I have all the...
I have a 2006 (K6) DF200 4 stroke with a 25in shaft. What is needed to change the motor to the shorter 20in shaft. I am taking it off my saltwater boat and want to use it on my Bass boat. Can this...
What shaft length on the Suzuki are you planding to use on your bass boat? I have a DF200 with a 25" shaft I am planing to put on my Stratos 295PE. With my 6" jack plate it measures up to one set of...
1999 Evinrude Fitch 150 on 295 PE Stratos. How to decarbon engine? My rude 150 has never been decarbonized, runs good mid to full throttle. After idling or running slow (no wake zones) the motor...
I am looking for some reasonable priced shad minnow plastics (3" to 4") for an A-rig. Anyone have anyone have any places on here that might have them?
Is there any sealer that you can use on the cork handles of rods to seal out dirt and make then easier to clean? http://www.bassboatcentral.com/smileys/praying.gif