Sent you a PM.
Type: Posts; User: Hoss Triton
Sent you a PM.
Calls for 60A breaker. If your boat is older & had 2-40A breakers, you need to upgrade to 1-60A . Its in Minnkota instructions.
I use old hay baler belt to mount & shim my TM's when I mount them. Cut same size as bottom of TM mount. If angle is an issue, shim up with another layer or 2 on the end that needs to be raised....
As long as wire to front is 6ga. or 8ga. minimum(Most are). You've got the correct setup as you described.
Don't forget to upgrade breaker from 40A to 60A. This is called for in the Minnkota...
Personally I would use 4200 for some flex & longer life as a seal material. 5200 IS permanent, sets up hard, & when it cracks, you're right back to square 1. Not sealed. Plus hammer & chisel to get...
Tx Champ & grout-scout. Make sure livewells drain valve is in "closed" position when using pumpout. Since y'all upped the gph of pumps, it is sucking air from the drain side(if valve is open/or NOT...
You're thinking right. Set motor on slotbox, Pull top 2, loosen bottom 2 & jack up trailer tongue. Put top 2 in, tighten them, tighten bottom 2 (slotted). I like your idea of slotted box to support...
WHY are Dealers not supposed to sell motors in a box? Jayco Marine has for years & is one of the BEST priced also. They'll ship to you. As long as a dealer verifies & registers it to Yamaha, theres...
E-bay has some nice ones from $250 to $375.
Has Chrome bezel & Voltmeter,Trim,water temp,water pressure on one of them. Im looling for correct Command Link multi function Tach gauge for mine.
Yamaha Command Link. But good luck on staying below $500 for gauges & harnesses
Beede, Faria are 2 brands to look at .,Im doing same . I want the multifunction Tach. It shows RPM,Trim,Oil,Overheat,Trip Hrs, Total Hrs. To get Fuel it is a second gauge showing Fuel...
Weston. It had worn the ends of the ring back about .010 on that piston,the L cut is messed up on ring ends. so it had a gap that was letting compression go by. The bulge was in the area above the...
You make a very valid point. I don't know the rep. Mechanic told me about that part of it. The rest of it i personally DID see for myself.
Might be a wise realetively small investment for owners to...
92 Champion re rigging dash & want to upgrade from (6)individual gauges of different sizes. Larger (Old speedo,tach & flasher)& 3 smaller(trim,fuel,temp) to (2)Yamaha Command link multifunction...
FWIW: just a tip to give longevity/strength to your plywood decking. While you have it exposedbefore recarpeting, use a thin coat of fiberglass resin to "seal" it. It also wil help fill in previous...
I bought my 98' Tr20 with a 150 Johnson FICHT on it. I ran great with only 372 hrs on it. BUT....You WILL NOT BE HAPPY with the holeshot & it'll wear that motor out quicker. Its a LOT of boat for any...
Positive
Price on a Black powder coated
8" for a 4.2L Yamaha with gauge?
Pole seat on back deck, extension(either bought or home made. Buy it & enjoy fishin with them boys. My 184 was one ( I'm on my 7th) of my favorite Champions. Sport car handling & rough water,dry...
Beautiful rig!!!
Kudos to Pat Goff. You are blessed to live close to Pat. He's THE man to set your Champion up & lots of advice to guide you. You'll have an Ace in the hole for any hand you get dealt on the trail!!!...
Thank you so much. Hopefully mechanic can get to it this week & diagnose what I'll need.? He saves me a lot of money. I save him time by getting the parts lined up ahead of time & in hand, so it...
I dont have a Merc manual & am NOT good on electrical system issues. Wanted part #'s so I could get an idea $wise what I may be looking at if it is a stator issue. Mechanic replaced both voltage...
I also have a question up. Can't access either.
Serial# OG000925
94' Merc 200XRi rebuilt & just coming out of double oil breakin period. Using non ethanol 87 octane premixed at 50:1 now.
I had burnt bullet connectors on my voltage regulators....