I think I know him ..... live's in Birmingham now and has been looking for a good shrink. wtgordon@charter.net
Where you at now?
Bill
Type: Posts; User: wtgordon
I think I know him ..... live's in Birmingham now and has been looking for a good shrink. wtgordon@charter.net
Where you at now?
Bill
Thought I would pass this along from a director of the Alabama Bass Federation Nation
Just dropping a line to keep everyone informed of the latest developments. I attended the Alabama Conservation...
Thought I would pass this along from a director of the Alabama Bass Federation Nation
Just dropping a line to keep everyone informed of the latest developments. I attended the Alabama Conservation...
They are meeting on it this Saturday. If passed, it will be law very soon.
LEGAL SECTION DRAFT 08/26/2008
STATE OF ALABAMA REGULATION 2008-MP-1
(Marine Police)
MONTGOMERY COUNTY
...
Last month I had a minor collision in the middle of Lake Martin around 8 am. I presumed I had hit a floating log that was deep enough that I could not see it. I stopped and raised the motor but saw...
Now I know what it looks like from the other side http://www.bassboatcentral.com/smileys/smile.gif
From the top, its hard to tell where the river ends if you are not paying close attention to...
Thats what I thought but wanted to make sure.
Thanks
I have the factory lower unit on my 04 HPDI and the skeg appears to be bent to the side. Is this normal? If so, anyone know any speccs on this so I can tell if it is out of kilter?
Thanks
Well the picture came out quite small but my guess is thats at least a 20 inch rule. The smallest fish about 3 and the largest about 5? I sure miss that lake.
Nice catch!
Nice looking truck. Shuldn't have any trouble at the ramp with that one. http://www.bassboatcentral.com/smileys/glasses.gif
Was just wondering what spare items folks carry for thier boat. I finally have a spare prop but also carry a plug, fuel filter, TM breaker, TM prop, and TM pin. Anything else I need to keep in the...
My motor normally runs about 15# or so at WOT. Last weekend I noticed it at 28# on one run, 15# the next, and back on 28#. Any ideas? Could this be trash in the system?
Thanks
There's defintely a few tigers lurking around here.
Here is the link for the Opelika-Auburn News.
http://www.oanow.com/
I know what you mean. The best price I can get on the oil is $18/gal with over a 3 hour drive. Fortunately, work has me drive by there from time to time or I would be stuck with $25/gal. The same...
I would add it now. I have used both at the same time with no problems.
I've always been a fan of grey carpet regardless of boat color.
Ok guys, it's time for me to dive into the modifications I've thought about since last summer. My 202 with a 225 HPDI has a hydraulic jack plate that provides a total set back of 10 inches. From...
I'm paying $550 with a $500 deductible with progressive. The deductible decreases $125 a year each year without a claim. It also will pay full purchase price in the event it is totaled. This was...
From Louisiana, lived in Alabama 8 years, and now reside in Pensacola, FL.
I have to agree with the others in that the edges come loose too easily. I am going to have to install some type of trim before it all comes up.
Sure are some good looking Blazers out there. Here is a pic of mine.
http://bassboatcentral.com/Blazerpics/Gordon1.jpg
After all of my recent problems, I would have to think its a filter. Mine turned out to be part #13 in the pic above. It only takes a second to remove it and look to see if the fuel is draining out...
Well I finally have the motor running great again as of today. It turned out to be nothing more than the water separator filter.
I'm new (3 months) to the performance boat group and I am looking for a new prop and some setup help. My current prop is a 27M and gives me 5600 RPM, 25 psi, and 73gps with a full load. I do not...
OK, I got a look at the prop today and it looks fine. The rubber hub looks like it has shrunk end to end as compared to another prop that I looked at but it was not the exact same prop either. ...