already repaired, thanks. Mods can you delete this thread. Thanks
Type: Posts; User: bassmasterfred
already repaired, thanks. Mods can you delete this thread. Thanks
Looking for a rebuilt or salvaged Lower unit from a yamaha 200 HP HPDI Vmax 2 Stroke 2005 or newer
Part number 6P5-45300-10-NA
I did replace the pads with the Kia organic ones....it was a tight fit as I couldn't get the caliper piston to close enough with a C clamp, however, I bang the caliper on with pads in place. Parking...
Chris at Ranger in the trailer department told me you can use 1996 - 2000 Kia Sephia pads. I believe you might have to break the corner tabs off of them, but not sure yet. He also said to use...
And if you get the handle to set tightly......and it still rolls a bit....does that mean new pads on the rear tires are most likely needed?
Thanks mullanator66, that does seem to be also an issue, pads probably thin now, hopefully not cutting rotors yet. Do you think the cable is broken at all? It loosed up....which is probably because...
Have a 2014 Z520 with the Ranger Trail Parking Brake and forgot to release it and drove to the ramp. Now the handle moves easily up and down (no locking feel) and the parking brake no longer holds. ...
The new Ultrex looks great for many applications but I'm wondering how it will do in 2 feet of water in thick weeds, pads, rice, etc? Will it cut through the weeds as well as my Fortrex 112lb?
...
thanks a bunch
Ghost, I have a 2014 z520c and would like faster hole shot and bow lift in rough water.....25.5p is your suggestion? I've read others use 26p....I only want to buy once....it sounds like Mercury has...
Thanks, I'll call him
Thanks...need to leave it on the trailer to make it useful. But thanks
Hi fellow MN bassers. I'm new to the area and my new home in Minnetonka won't fit my Ranger z520c. I'm in search of easy in/out access so I can fish often....then I guess some type of longer winter...
Ejevans45, thanks for comments. I didn't do the back yet.....not sure if I will or not. Once I removed the buckle it was easy to see the conduit...but it's more like a hose from your shopvac. ...
Thought I'd share my LED project. I used Oznium LED bolt type lights in two colors. Size 11mm with no lens, black casing. I chose these because of their sleek clean look and low cost. Even though...
torq thrust II are very nice looking. My problem is my GMC Denali has rims that look more like the American Racing Casino....so I'm trying to come up with a good solution. The Ranger Bullet wheels...
I've been doing a lot of research and there are limited choices due to the "offset". The American Racing Casino looks great but the offset is 42mm....which is about an 1.6 inches.....so I'm trying...
UPDATE - I called Ranger and the setback I was seeking is actually called the "Offset". These Ranger wheels are 17x7 with 0mm offset and a 5/4.5" lugnut pattern. The tire they suggest is General...
I'm looking to upgrade my z520c wheels from the Raptor to the chrome 17" wheels that Ranger sells. The cost is crazy from Ranger at over $345 per wheel before adding the tire itself. Found...
I did get the gauge working. Everything was dressed so nicely and zip tied up....I looked but couldn't find an empty pigtail. I took the easy way out and spliced into the oil gauge which was close...
they said they think there's an extra "Deutsch Connector"....unless there was an oil fill gauge added.....which I do have that gauge. I'll be looking carefully soon for an open connector
Thanks Lou, yes I have the Stealth info....my problem was everything is covered, wrapped, and shrouded underneath the console on the boat and trying to access anything under the dash. I know where...
Called Ranger and they are saying there might be an open run to tap into depending on what gauges were ordered with boat, if nothing is available, then just splice into Purple - hot from key switch ,...
Yes, installing the Stealth 1 Charging system, everything has gone nicely until I started working on this gauge.....and underneath the dash on this new Ranger has changed. I've got a call into...
Thanks Jones,
I'm adding a new digital voltmeter. On my last Ranger I replaced the needle voltmeter with this same digital and it was easy because all my wires were on that gauge. On this new...