Search:

there really isn't enough information here to make a determination. Normally, on machinery etc I always start with the most simple issues before working up to the more complicated. Here, there is a...

take it to a radiator shop and see if they can clean it out.

Wildwood on the exterior, and 3M on the interior lips where you fold the carpet in.

Have you noticed fuel leaking anywhere while the pump is running? Specifically, from the foot of the engine or pooling in the cowling. I had a similar issue where a couple of o-rings on the...

3M Vinyl conditioner and cleaner with a fingernail brush.

Whatever you get make sure that you get a clear title to boat and engine with it. Trailers under 4000# do not need to be titled in Texas, so the registration works for the trailer. However, no...

Last year, my trolling motor died just a about four days before our annual guys trip. I am about three hours south of Texarkana. Called John and talked to him about the problem. He asked me if I...

But did you check the voltage at the fuse box? That is did you have 12vdc coming into the fuse box? Do you have power on both sides of the fuses and relays? You need to check this. By doing this...

I used an awl to find the hole and install one bolt. Then a small drill bit in a cordless drill to drill through the carpet while using the hing plate holes as the template. It's pretty fast this...

If you are running an adapter to go from 7 pin round to four or five pin flat make sure and ohm out the adapter to determine whether it is bad. Check the simple stuff and work your way to the more...

Some soldering irons actually have an x-acto blade that you can screw in. It heats up and is sharp.... best of both worlds!

If you need to add fluid then it went somewhere. Brake fluid attracts water. So if you have a leak water can get it as well. See if you can find the leak, and then bleed the entire system till you...

I found funnels at an RV store in Dallas while there with a friend picking things up for his camper. It was one of those damn why didn't I think of that moments. The funnels have a screw lid on...

I used a wire cup brush on a 4 1/2" grinder. Go slow, and be careful, but it worked very well. Wipe down with acetone when done to remove the dust.

I had the same issue with my 97 175 EFI and it was a faulty alarm module. May or may not be your problem.

Yes, you apply to both surfaces. For the lids I would lay them on the carpet, backing up, and mark the edges of the lids. Then put the cement inside the boundaries of the lines. Cement the top of...

I've been using RONEX MP in everything from lawnmowers to boat trailers for years. Had really good results.... at least no failures in anything. I got tired of buying multiple greases for different...

I used Weldwood contact cement for the large flat surfaces like flooring and lids. 3M Super 90 pray on the inside of the lids (where the carpet rolls underneath the lid), and a few small carpeted...

If you had to add fluid then it obviously went somewhere, if it was full at one time. This usually means that you really need to bleed the system when you add more fluid. As said above, you can get...

Once you get the link and synch done change your plugs.

Hey, it could still be a jet/carb issue. I'll leave that up to the experts to decide. Good luck!

Ummmmm, Don is the expert, and I would surely follow his advice to the letter. However, being from Texas the only place that I know that has 8000 feet of elevation is far west Texas around the...

I did it, at Don's recommendation. Don't remember the place but believe it was in CA. Excellent service. Ran about $600 if I remember right. It turned out not to be my ECU, but it did have loose...

Maybe... Maybe not. However, it is never a good idea to run anything with the battery disconnected. It can do major damage to electrical components.

I have to second this. Not to knock Blue Water, since I love their LED's, however the LED strips work great for boat compartments but just are not bright enough off the rear of the trailer to do...