Search:

Type: Posts; User: JonNovak

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    206

    i looked at the diagram for the fortrex and its...

    i looked at the diagram for the fortrex and its listed as chrome. i was hoping maybe i could get one from a salt water version, riptide or something that would fit
  2. Replies
    3
    Views
    206

    Fortrex lower shaft bearing rusted

    my lower shaft bearing about froze up on me. can i get a replacement thats gonna not be effected from brackish water? i dont fish salt water but had ventured out there last month and it was a little...
  3. Replies
    5
    Views
    3,095

    Yes sir. Inline 4 cylinder 115. Serial 0t106278

    Yes sir. Inline 4 cylinder 115. Serial 0t106278
  4. Replies
    5
    Views
    3,095

    been searching more. i wonder if i swap warning...

    been searching more. i wonder if i swap warning module from the 1993 115 and see if i get the key on beep
  5. Replies
    5
    Views
    3,095

    Nope, no beep with key turned to on position

    Nope, no beep with key turned to on position
  6. Replies
    5
    Views
    3,095

    2000 Mercury 115, no beep during key on

    I know the beeper works. worked with my 40hp and worked with the 1993 115hp motor.
    with the 2000 115hp motor i get a constant beep with key on. tracked it down to oil tank magnet/float being bad by...
  7. Makes total sense. New diaphragm stiffer won't...

    Makes total sense. New diaphragm stiffer won't pump even at higher rpm. I guess it's quitting time..
  8. gonna try to put a T fitting in fuel line after...

    gonna try to put a T fitting in fuel line after fuel pump with shut off on each out of the T and run the motor then switch over and see if fuel pump is sending fuel out.....if i can find all the...
  9. no dice. motor keeps running out of fuel for some...

    no dice. motor keeps running out of fuel for some reason. how much crap do i have to rebuild twice?

    maybe i did something wrong. it wont even keep a high idle now without running out of fuel in a...
  10. how the %&#% am i running out of fuel. same deal...

    how the %&#% am i running out of fuel. same deal as before. pump firm while running will idle nicely. stop pumping and its running out of fuel. with motor off i pump it up as hard as i can and get no...
  11. check valve certainly is working in fuel pump via...

    check valve certainly is working in fuel pump via the mouth blow suck test. fuel pump was rebuilt with a kit, all new gaskets and diaphragm same order it all came apart. but i did just re-tighten all...
  12. Tube, Idle...

    Tube, Idle !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

    thats what parts list this as. parts i couldnt get to last time. i almost gave up again. i just about ruined the screw trying to...
  13. every time i have to pump it back up before itll...

    every time i have to pump it back up before itll start again i can hear the top carb filling but not the bottom 2
  14. yeah so ok, keep pumping will idle lower. stop...

    yeah so ok, keep pumping will idle lower. stop pumping and itll die in 30 seconds to 1 minute. crank crank crank nothing. crank crank crank while squeezing bulb and once firm itll fire
  15. rebuilt fuel pump. old diaphragm didnt look to...

    rebuilt fuel pump. old diaphragm didnt look to bad. inside was very clean.
    open idle mix screws 1/4 turn each. bypass (new) fuel filter since it seemed to empty without staying remotely close to...
  16. why, are they expensive or tough to change and...

    why, are they expensive or tough to change and seal new ones? i only have 500 into this motor. 200 purchase. plus 100 in gas to go get it, plus couple in parts so far, mostly bottom end stuff to...
  17. pulled all the idle screws out, cleaned in each...

    pulled all the idle screws out, cleaned in each hole and the needles themselves. reset to 2 1/2 turns out, later adjusted out another 1/4.

    reset all the butterflies to 100% closed. adjusted the...
  18. no idle stabilizer on this motor. parts list and...

    no idle stabilizer on this motor. parts list and diagrams show it never had one from factory.
    started it up other day and now my tach on dash stopped working. pulled tiny tach off other boat and...
  19. motor has a date written on top of power head in...

    motor has a date written on top of power head in grease crayon. maybe from factory. appears motor is now a 1983
    not sure about the idle stabilizer thing. ill look into that
    ordered fuel pump...
  20. 1980 90hp, dies when put in gear, idle to high

    dies when put in gear while in water only. on hose it shifts fine. cant get the idle any lower than 1,200. in order to move in water i have to rev it then shove it in forward once its warmed up. if...
  21. the lady at west marine is such a snot. hopefully...

    the lady at west marine is such a snot. hopefully the right parts come, but the upper water pump housing picture didnt look right
  22. Yeah I figured but hard to find the ones I need...

    Yeah I figured but hard to find the ones I need without knowing the year. I tried looking up the serial and come up with not found
  23. 90hp tower of power, serial, water pump, shiftshaft seal

    serial number 5672490
    tested compression other day and fired it up on the stand today.
    shift shaft seal was causing water to get in. water pump is in bad shape so those are the parts im going to...
  24. Replies
    2
    Views
    160

    Appears to be 3 or 3 1/16'inch?

    Appears to be 3 or 3 1/16'inch?
  25. Replies
    2
    Views
    160

    Spanner nut 11-87763, thread chaser

    before i got the boat the guy put the prop on without thrust washer. killed the spanner nut, and couple of the starting threads are kinda ground down. i can not get the new nut to start. i got the...
Results 1 to 25 of 186
Page 1 of 8 1 2 3 4