I appreciate your help and will be more aware when posting next time. Thanks guys, tight lines!
Type: Posts; User: tylerandrews02
I appreciate your help and will be more aware when posting next time. Thanks guys, tight lines!
The cap on the oil reservoir has repeatedly came loose and oil over flows. I have replaced the cap once and problem persists. I notice that over tightening of cap does not work - seems to roll over...
New to Garmin and adding livescope unit to my boat.
Will an extension to the transducer affect the image quality? My idea is to leave the extension ran through my boat for easy removal during...
I have a 2015 Ranger 520c and the rod locker has the tubes in it. I keep rod socks on all my rods and it gets hectic in there with 20 or so rods. Has anyone taken these tubes out? I know Ranger has...
So I have the ultrex but not i-Pilot link. Does this mean I would need the AS GPS HS?
I have 3 G3N connected via Ethernet. My graph running 360 doesn’t show waypoints on the 360 lay out. What sort of heading sensor or gps sensor do I need to show my waypoints on 360 and how to I rig...
How do you all clean your carpet? Mine isn’t trashed by any means but could use a good cleaning. Thanks in advance.
Looking to buy some power poles from someone local. Looking for a set of 8’ blades. Let me know what you have. Thanks!
Does anyone have a picture of how they have their MSI transducer rigged on a newer ranger? I am replacing a Lowrance transducer that was siliconed to the bottom of the boat (just in front of the...
I know this sounds like a really idiotic concept. However, I just hooked the power cables on the helix’s to the power supply that was already in the front of my ranger. Everything seems to work...
If I could figure out how to compress a photo to upload to this website, I’d gladly include one for you ^^
I currently have 2 helix’s stacked at the bow of my boat with M360. Adding a 12” unit at the dash. Contemplating the solix vs helix for my dash unit. Am I losing out by networking a solix to a helix?...
I flip flopped the positive and negative on the power supply at the front of the boat. Still only powers up if power cord is upside down.
Transferred 2 G3N helix 10s to my new boat. They will only power up if the power cord is plugged in upside down. The problem is they won’t fit in the cord organizer because the mold has them placed...
Thank you. I know it works because I’ve used it several times, however I’ve had it flash at me twice now. Going to have to check for debris in it.
I have not checked the voltage at the battery. However, the reason for running new power to the 360 is because it won’t work if connect to the power supply at the front of the boat. If I connect it...
I have 2 helix 10s stacked at the front of my boat. Currently they are ran off the same power supply as my heading sensor, bow lights, etc. They work fine. However, I am going to run new power to my...
I’m new to a 2015 ranger z520c. Occasionally the main bilge pump light will flash and have to push the auto bilge button to pump water out. Any ideas why? Also, what’s the purpose of the auto bilge...
The gauge is a mercmonitor. The serial number is 2B090081 - 2015 Merc 250L Pro XS. There is no tone with the alarm. The mercmonitor reads 0.0 for oil tank. I apologize for missing the announcements...
Awesome, thanks for the help guys. I’m going to go with the 87 and call it good!
I’ve checked that one several times in fear of it running low (due to the oil alarm), But each time it’s full.
My oil alarm remains on regardless of the tank being full. Just put 2 gallons in and the smart craft gauge still reads 0.0L. Any ideas? 2015 250 pro xs. Thanks in advance.
I recently purchased a boat with a 250 Pro XS. The previous owner ran only ethanol free gas in it. I’m wondering if this is a must or if I can run premium with no worries? Note: the power head was...
Has anyone trimmed down the shaft on the 360? The shaft on the ultrex 360 is quite long and gives very little room for adjusting the TM shaft? I also noticed on KVDs boat, his shaft is cut flush with...
Thanks for the help Wayne. I will have to double check connections and scrub the water sensors.