Search:

Type: Posts; User: Z20Tim

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    177

    Best upholstery shop in Abilene?

    Any ideas?
  2. Replies
    4
    Views
    321

    My thinking is they didn't have a big enough...

    My thinking is they didn't have a big enough capacitor originally, seeing how the injector system is a 55 volt system they need something to handle the 55 volts
  3. Replies
    4
    Views
    321

    2006 Etec 225 Capacitor question

    2006 Etec 225hp E225DHLSDF

    So I have had 2 fuel injectors go out, and a fella on here told me I should also change the capacitor, I finally got around to it and noticed the new one was about...
  4. Replies
    3
    Views
    189

    Thanks!

    Thanks!
  5. Replies
    3
    Views
    189

    Need Fuel Injector

    Best place to get a 2006 Etec Evinrude 5006221 fuel injector
  6. Replies
    31
    Views
    3,170

    Are the crush rings inside the housing? Wasn't ...

    Are the crush rings inside the housing? Wasn't gonna take them apart
  7. Replies
    31
    Views
    3,170

    Thanks for all the info, I'll get the injector, ...

    Thanks for all the info, I'll get the injector, what kind of solvent can I use just to clean these up a bit?
  8. Replies
    31
    Views
    3,170

    So if you were me, would you spend the money on...

    So if you were me, would you spend the money on cleaning, or just by a new injector here a pic of all my port injectors, also, not sure if I mentioned I been running
    xd100 while on the tcw3 xd50...
  9. Replies
    31
    Views
    3,170

    Starting pulling injectors thinking I'd send them...

    Starting pulling injectors thinking I'd send them in to clean and test, pulled port side 1st, #6 rattles where 2 and 4 don't. Is this normal? Good,bad, ugly?
  10. Replies
    31
    Views
    3,170

    Ok, that's what the sticker says on the EMM, ...

    Ok, that's what the sticker says on the EMM, well looks like
    I'll be ordering a new injector this make # 2 that I've replaced, guess I'll do one at a time.
  11. Replies
    31
    Views
    3,170

    So, I also noticed that the #2 LED is not on when...

    So, I also noticed that the #2 LED is not on when the ign is just set to "on" mode. According to manual this is the injection ignition light. Is that telling me its a bad injector?
  12. Replies
    31
    Views
    3,170

    Yep, that didn't work, pretty sure when I sent...

    Yep, that didn't work, pretty sure when I sent them into Fuel injector man 2 years ago #6 was weaker than the rest.
  13. Replies
    31
    Views
    3,170

    Cool will do, I was a little nevers about messing...

    Cool will do, I was a little nevers about messing with that control. #6 inj is definitely clicking
  14. Replies
    31
    Views
    3,170

    Update: got the ETec diag software, did dynamic...

    Update: got the ETec diag software, did dynamic ignition check on all 6 cyl, all but #6 bogged down, no change in idle when #6 tested. Did the injector test same thing. Then did static test...
  15. Replies
    31
    Views
    3,170

    The fuel lift pump or the vst pump?

    The fuel lift pump or the vst pump?
  16. Replies
    31
    Views
    3,170

    Ok, I guess I got click happy on the pics lol. ...

    Ok, I guess I got click happy on the pics lol. But is the filter collapsed because it's so clogged or is there something else to look for. Also where does all the crap in fileter come from since...
  17. Replies
    31
    Views
    3,170

    The other 3 look just like it

    The other 3 look just like it
  18. Replies
    14
    Views
    728

    Where did you get a new VST filter? Here's what...

    Where did you get a new VST filter? Here's what mine looked like I also have the newer vst.413259
  19. Replies
    31
    Views
    3,170

    2006 Evinrude Etec E225DHLSDF bogging down

    After slow rolling up a creek (almost idle) on the way back ran fine for about 1/2 or so then when I stopped takes forever to get on plane, when it finally does get to about 5000 rpm, cleaned...
  20. Replies
    1
    Views
    210

    New brushes on MK Fortrex

    does it matter if you mix up the pos and neg on the when changing the brushes. Pretty sure I have the the way they were. But there is no marking for pos or neg.. propeller is turning the right...
  21. Replies
    4
    Views
    276

    Probably bent the aluminum out shaft. I did the...

    Probably bent the aluminum out shaft. I did the exact same thing when I lost my lower unit. Jacked up all kinds of stuff. The bearings blew out on the outer shaft also.
  22. Replies
    7
    Views
    322

    Did the armature test, looks like that's the...

    Did the armature test, looks like that's the culprit!!! Marked it with tape when it stopped here's a pic of the spot where it won't spin.398878
  23. Replies
    7
    Views
    322

    I adjusted the reed switch ended up applying...

    I adjusted the reed switch ended up applying epoxy to keep it in place, seemed loose. Thought that was the fix. Went back to lake same thing. There is no sound from relay, seems to start working...
  24. Replies
    7
    Views
    322

    Fortrex 112 intermittent

    I took apart my trolling motor because it's been intermittent, here are some pics of armature and brushes do they look bad?398658398658398659398661
  25. Ranger parts has them, right around $200

    Ranger parts has them, right around $200
Results 1 to 25 of 72
Page 1 of 3 1 2 3