Search:

Type: Posts; User: triton1cos

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Fuel Filter

    by triton1cos
    Replies
    7
    Views
    561

    Re: Fuel Filter (Dutch552)

    i agree,i replace mine every fall when i wnterize,change gear lube then too.
  2. Re: (Mark Tr.)

    just keep it verticle all water will drain there will be none in block to freeze.also i would recommend xd100 in the cold temps if ya aint runnin it already.
  3. Replies
    6
    Views
    532

    Re: Asphalt work in louisville (uk2thdoc)

    streigel will do ya right. Pete is a good guy he is the owner.and he would appreciate ur business.Tell em Bill at wennings paint and body recommended them!
  4. Thread: 36v TM ?

    by triton1cos
    Replies
    15
    Views
    586

    Re: (Catch 1)

    why in the heck would anybody want or need a 36volt tmotor on a 1300 pound boat?
  5. Re: I need help/ direction to find the cause of my problem (Kromer)

    sounds like its going into slow mode fer some reason.no water? no oil?
  6. Replies
    4
    Views
    314

    Re: Valve Tapping from a 2-stroke 200XP? (puckstopper)

    couldnt be a valve there isnt any.well except reeds.
  7. Replies
    5
    Views
    305

    Re: HD 50 oil for E-tec (Bassmeister)

    bulk is the way to buy it will save u around 40% of pre packaged gallons!28-30 bucks vs 50
  8. Replies
    2
    Views
    395

    Re: lu drain plug (DoferGofer)

    i pumped about a half pint of lube in top hole and rinsed shavings out.i figure aluminum shavings aint gonna hurt metal gears anyway!
  9. Replies
    2
    Views
    395

    lu drain plug

    doh,took plug out and changed oil put plug back in it would not tighten threads stripped.whats the norm to fix this.not plug but threads in lu.i repaired it with heli coil redrilling and taping hole...
  10. Replies
    12
    Views
    1,698

    Re: (Bassmeister)

    that could be from condensation!rest of oil is not the norm looking milky with water in it.i would change then run and check it again.large amouts of water will drain out before oil and rest of oil...
  11. Replies
    13
    Views
    462

    Re: Trim extenders (Gsmith223)

    i agree on prop,not enough lift in it what kind of prop and what motor and boat
  12. Replies
    2
    Views
    152

    Re: 2005 E tec gear ratio? (jimt54656)

    it has 1.85 gears it is the lightning gearcase same as mine.
  13. Replies
    4
    Views
    1,485

    Re: bobs outboard engine exhaust housing (bcbassking)

    opening up exhuast like that will give ya a few rpms 50-100 but mph gain will be maybe 1 mph.thAT is my experiance with it on an evinrude 150 about 20 years ago...
  14. Replies
    15
    Views
    1,774

    Re: (T Dub)

    so http://www.bassboatcentral.com/smileys/wink.gif get a gel boat with flake stripes!
  15. Replies
    17
    Views
    1,426

    Re: USA Bassin Regional at Patoka (cosmo6345)

    patoka is far from a dead sea.it has been better the last five years than it ever has.lots of 3-4 pounders and keepers in that lake.25 pound bags to win last gota luv it and hoosier...
  16. Replies
    26
    Views
    2,834

    Re: (ep72)

    its hard to repair plastic like that and get it to last though i guess it could be done with some plastic repair .if it were fibeglass wouldnt be a problem.i aint gonna attemp it.but u get it fixed...
  17. Replies
    26
    Views
    2,834

    Re: (Matt Mc)

    http://www.costacamocoating.com look in gallery to see samples of carbon fiber ,skulls ect.the drink holder was for a houseboat dash it was smoke plexiglass and steel tubing before coated in...
  18. Replies
    830
    Views
    462,383

    Sticky: Re: (Bharris)

    bharris,put a older 28 raker on that 20x not a raker2 but one of the late model plain rakers.i run a raker on my 21x etec 225 and can hit 77 with the load u discribed.them 20' tritons are close to...
  19. Replies
    26
    Views
    2,834

    Re: (signmanbasser)

    signman, reply sent take a look at my site u will see the skulls and some red carbon fiber.
  20. Replies
    26
    Views
    2,834

    Re: (triton1cos)

    yellow carbon fiber Lou!!!bad arse in ur boat http://www.bassboatcentral.com/smileys/eek.gif http://www.bassboatcentral.com/boardstuff2/pimp2.gif
  21. Replies
    26
    Views
    2,834

    Re: (triton1cos)

    Matt,send me ur peices give me a color i will coat them in carbon fiber and send them back to ya.If you dont like em i wont charge ya!i am willing to do this one time to get these guys exposure to...
  22. Replies
    26
    Views
    2,834

    Re: (Largemouthlou)

    lou,ive been doin it for a couple years.the patterns(prints)are just about endless more than u can imagine.ive put everthing from skulls on harley helments to camo on guns.custom color carbon fiber...
  23. Replies
    26
    Views
    2,834

    Re: (Matt Mc)

    really doesnt matter what color they are i can coat them if you have the panels.
  24. Replies
    26
    Views
    2,834

    Re: (Matt Mc)

    do you have the original woodgrain panels?if so i can coat them in carbon fiber (any color base red,blue,black,purple ect ect)or derectional kevlar look or many other prints including...
  25. Replies
    24
    Views
    1,557

    Re: (21XDC)

    just make sure if its painted they use ppg delfleet evolution or dupont emron 6000 and there clears.we use ppg in the shop and we specialize in fiberglass hoods and semi trucks.its the most durable...
Results 1 to 25 of 411
Page 1 of 17 1 2 3 4