Search:

Type: Posts; User: Jwebre74

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    472

    Mercury 300R gearcase oil change

    S# 1E080694 Mercury 300R

    How much oil do I need to refill my gearcase once on drain it? I thought I read where that Manuel says 21oz, is this correct?
  2. Thanks for your help

    Thanks for your help
  3. You are saying I’d be able to use my same 3D...

    You are saying I’d be able to use my same 3D transducer without the module?
  4. Lowrance Lss2 transducer setting question

    I was running the 3D structure scan module and transducer but my module isn’t working anymore. I pulled my 3D transducer and module and installed my old lss2 transducer until I can get my module...
  5. Replies
    4
    Views
    510

    Solix vs helix

    I’m gonna be switching to hummingbird units and was wondering which units would be better. I’ve heard that the solix draws my power and has a slower processor. Can Anyone can give me some feedback on...
  6. Sounds like a low voltage issue

    Sounds like a low voltage issue
  7. Replies
    3
    Views
    320

    I’ve looked back and it’s been removed, unless...

    I’ve looked back and it’s been removed, unless I’m looking In the wrong place
  8. Replies
    3
    Views
    320

    18.2 software update for carbon

    Does anyone have the 18.2 software update that I can use to roll back my carbon units.
  9. Thanks. I’m hoping it’ll give me better images....

    Thanks. I’m hoping it’ll give me better images. I’m currently running 4.0 and it’s not all that good.
  10. Replies
    3
    Views
    284

    I had the same problem last week. Are you running...

    I had the same problem last week. Are you running the 3D module? I had a bad connection on my Ethernet cable. I cleaned it and now it works fine again
  11. 18.3 Update for Carbon and structure scan

    Does anyone know where I can get the 18.3 software update for my carbon unit and SS3D ?
  12. I’ll change the Ethernet cables and see if it...

    I’ll change the Ethernet cables and see if it clears up. It’s a funny thing bc the last time I took it out my images were crystal clear and then bam it started doing this .
  13. Lowrance carbons/ 3D structure scan issue

    I started having a issue with my down/side scan. I’m running 2-12” carbon units with the structure scan box and this pass weekend i was scanning and the screens went out and across the screen No...
  14. Thanks, I’ll double check everything

    Thanks, I’ll double check everything
  15. Lowrance Carbon with 3D structure scan question

    I currently run 2 carbon units and have the 3D structure scan transducer mounted on my jackplate. My images are ok but I’m wondering if there’s another transducer out there that would help me get...
  16. Replies
    1
    Views
    413

    Mercury 300R Alarm code

    I got an alarm code “STB” Engine sensor, Manifold absolute pressure sensor and throttle position sensor do not agree. Does anyone know what this may be? It’s going to the shop in the morning but was...
  17. Replies
    28
    Views
    2,315

    Open for another year.

    Open for another year.
  18. Replies
    1
    Views
    463

    Lifting Eye for 300R

    I haven't had a chance to find my serial number but I'm assuming they are all built the same.Can I use the same Lifting eye that fits a 300xs to lift my 300R? Thanks
  19. Replies
    8
    Views
    1,708

    Only reason asking was I had roughly 30 gallons...

    Only reason asking was I had roughly 30 gallons or 93 octane fuel with aces fuel treatment in it which increases octane a little more. I didn’t plan on running anything but 87, I’ve spent enough...
  20. Replies
    5
    Views
    1,348

    300R Break in procedure

    Anyone can give me the break in procedure for the 250-300R motor? Got my motor installed today and didnt get any manuels.
  21. Replies
    8
    Views
    1,708

    300R Octane Fuel question

    Is there a problem running 93 Octane in a 300R?
  22. Replies
    2
    Views
    438

    C Bailey Polished stainless hydrofoil FS

    I have a polished stainless hydrofoil from CB marine I’m selling. It has Mercury cut into the sides with red backing. Comes with hardware. 100 plus shipping . Was on mercury 300xs sportsmaster lu....
  23. Replies
    17
    Views
    1,901

    300R Sportsmaster lower unit.

    300R Sportsmaster lower unit.
  24. Replies
    17
    Views
    1,901

    Transom saver for new v8

    Anyone know if the old style transom saver will work on the new v8 motors. I'm going get my motor installed Friday and will be traveling 8-9 hours.
  25. Replies
    20
    Views
    2,512

    Ordered my 300R beginning of August and it's...

    Ordered my 300R beginning of August and it's gonna be in today. Been a long wait but im sure itll be worth the wait.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4