Search:

Type: Posts; User: BlazerVA

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    29
    Views
    7,052

    When mine broke i went to this....

    When mine broke i went to this. http://www.blackbearsportinggoods.com/Fuel_Select0r_Valves_p/ellrrde100fsv.htm
    I was told the plastic ones were banned by the Coast Guard.
  2. Replies
    5
    Views
    343

    Right now I'm close to even with pad. I've got...

    Right now I'm close to even with pad. I've got the top 4 inlet holes plugged on each side of the LU. I figured if I put a LWP I could get the motor up with less chine. I reckon the prop would be...
  3. Replies
    5
    Views
    343

    TXP IV vs Bravo xs

    Currently running a 27p TXP IV level with pad on a Blazer 190. 10 inch jack plate. Motor is 2004 250xs with a torquemaster lower. I'm in the process of installing a low water pickup. With the TXP I'm...
  4. Replies
    50
    Views
    1,333

    I had a very similar issue with a 250xs. Mine...

    I had a very similar issue with a 250xs. Mine threw a code though for an open injector. Ended up being the wiring to the injector. Had a slight miss at low rpm and sometimes the alarm would pop on at...
  5. Replies
    27
    Views
    926

    I went to big on the first one. It was a 29p. I...

    I went to big on the first one. It was a 29p. I could only turn 5400 rpm with it but would run low 80. I'm also in a 190 prob. I traded it for a 27p TXP. Ran it today for the first time but the wind...
  6. Replies
    27
    Views
    926

    I was chasing the same issue. What prop to run. I...

    I was chasing the same issue. What prop to run. I just put a 250xs on my boat and had been running a 26p Trophy previously with a 200 2.5. I had always ran a Trophy thinking it was the best prop but...
  7. Replies
    10
    Views
    463

    29p TXP. I raised the motor up to about 1/2 below...

    29p TXP. I raised the motor up to about 1/2 below the pad. Ive gotta torquemaster so i can only go so high with it. Handled good up til about 78mph then got a little squirley. Im gonna bring it up...
  8. Replies
    10
    Views
    463

    Finally got around to a bigger prop. Think i went...

    Finally got around to a bigger prop. Think i went to big. About 300 rpm short of 5800. Can a prop be worked to gain that much or would the cost not be worth it? Holeshot was good, topped out at 82...
  9. Replies
    10
    Views
    463

    :yesnod:

    :yesnod:
  10. Replies
    3
    Views
    528

    The chine walks from the motor being low in the...

    The chine walks from the motor being low in the water. Whats your water pressure at when youre running? I'd raise the motor up on the plate 1/4'' at a time til you start to lose water pressure. Then...
  11. Replies
    10
    Views
    463

    I might give you a shout soon. Im gonna run a...

    I might give you a shout soon. Im gonna run a couple loaner props this week at some point.
  12. Replies
    10
    Views
    463

    190 prov with 250xs

    Just picked up a new motor. It's a 250xs 3L. Not the V8. First has anyone ran the 250xs on a 190? If so what prop were you running? I've gotta 26p Trophy I ran on the 200 I took off but it's in the...
  13. Replies
    9
    Views
    248

    Ive gotta 2002 with a 200 Mercury and im turning...

    Ive gotta 2002 with a 200 Mercury and im turning a 26p Trophy at 5700. The 25p Tempest i had put me over 6k. If you get low 70's with a 25p prop I'd be surprised.
  14. Replies
    16
    Views
    626

    The creek has good water in it. Fish the drains...

    The creek has good water in it. Fish the drains on the outgoing tide. I believe the second big turn has some rocks in the corner. Other than that youre good. When you run in there youre gonna go...
  15. Replies
    16
    Views
    626

    I spelled it wrong. Its Tomahund. When you go...

    I spelled it wrong. Its Tomahund. When you go under the rt5 bridge into the James its the first creek on the right. We were out there Monday during the rain and wind and did good there, the back of...
  16. Replies
    16
    Views
    626

    Definitely not on little creek. All the Suffolk...

    Definitely not on little creek. All the Suffolk lakes are 9.9 hp rated. I believe there's 6 lakes over there.
    As for the Chick/ James. When u launch at rt 5 your in Gordon's Creek which is as solid...
  17. Replies
    16
    Views
    626

    I was on Whitehurst yesterday for 5 hours. Ended...

    I was on Whitehurst yesterday for 5 hours. Ended up catching 25-30. Nothing big though. Largest around 3lbs. I grew up over your way. Those Suffok lakes are far better than a lot of places you'll...
  18. Replies
    12
    Views
    926

    I just bought 20 of them off Ebay for $2 each....

    I just bought 20 of them off Ebay for $2 each. They come from China and take about 2 weeks. Theyre good quality and cant beat them for the money. Just saying.
    Heres the link....
  19. Thread: Carb to EFI

    by BlazerVA
    Replies
    11
    Views
    494

    So far the linkage, intake, reeds and electrical...

    So far the linkage, intake, reeds and electrical for the efi are swapped over. Plugged the bleeds for the carb and ran the bleeds for the efi setup. Waiting to get the injectors back from getting...
  20. Thread: Carb to EFI

    by BlazerVA
    Replies
    11
    Views
    494

    Yes. Theres one on every cylinder.

    Yes. Theres one on every cylinder.
  21. Replies
    14
    Views
    579

    Have you checked out the stator?

    Have you checked out the stator?
  22. Thread: Carb to EFI

    by BlazerVA
    Replies
    11
    Views
    494

    Theyre both 2.5. I talked to a local guy earlier...

    Theyre both 2.5. I talked to a local guy earlier today who said he can do it without any issues. Hes gonna send the injectors off and redo the bleed lines, timing, reeds...the whole nine yards.
  23. Thread: Carb to EFI

    by BlazerVA
    Replies
    11
    Views
    494

    Is there a difference with the blocks?

    Is there a difference with the blocks?
  24. Thread: Carb to EFI

    by BlazerVA
    Replies
    11
    Views
    494

    Carb to EFI

    Im about to have a 200hp promag rebuilt. Im currently running a 200hp Blackmax which has carbs. The Blackmax runs good and has 120psi on all cylinders. Is it possible to swap the EFI stuff onto this...
  25. Replies
    12
    Views
    793

    Tax returns are in! Gonna make some moves here...

    Tax returns are in! Gonna make some moves here soon. Haha
Results 1 to 25 of 29
Page 1 of 2 1 2