I am looking into a CMap map card for South Carolina. I’ve looked over the options and see that there is a Reveal Southeast chip and a specific South Carolina Reveal precision HD card. Does anyone...
Type: Posts; User: Lodge06
I am looking into a CMap map card for South Carolina. I’ve looked over the options and see that there is a Reveal Southeast chip and a specific South Carolina Reveal precision HD card. Does anyone...
a friend of mine owns a machine shop. I had him make a similar support that would fit the original minn Kota support arm out of a block of aluminum. Had him make the bracket 2 inches longer so the...
I have the same trailer swing configuration. 2004 triton tr21X. Mine had play side to side and up and down. To much for me to be comfortable with while towing. Replaced the pins with grade 8 bolts....
I had a similar problem with my 94 merc xr6 150. Had intermittent beeps and after running tests in the manual it was found to be the nylon gear on crank shaft that turns the oil pump had stripped....
I had a 94 482v with a 6" manual plate. It had at merc xr6 150 on it. I found my best spot was 3 1/4"-3 1/2" below pad. I ran a 23p tempest plus. Great hole shot and performance. Would run around...
Something on the highway broke my transmission cooler line while on a road trip. I didn't notice for a while and my white Tr21x was covered in tranny oil spray. Anyone have any suggestions as to what...
My new oil tank assembly came with a new sensor so I ran a quick test before I installed it to make sure it was my problem. If you clip your wires at the sensor and tie them together and run your...
Your sensor tests were exactly how mine were. I replaced the tank and the beeping was solved. As for no oil flowing from the remote tank, that's got me. I know it runs off crankcase pressure which...
I had the four beeps every two minutes recently. I solved the issue by replacing oil tank under the cowl. The magnet on the float had failed causing the alarm sound. I tested the sensor wires (two...
Lucas hub oil or the SAE 50w?
Thanks guys. All the parts are on their way. Going to change out everything next weekend.
im going to be purchasing all new site glass hub covers. Is there an o ring that goes on these before you install? Or is there a groove on the inside of the hub where it sits? Or are you referring...
Thanks TRC. What oil did refill with? I really want to use the Lucas but the heavier weight makes me nervous.
CH so you run the Lucas hub oil and not 50w motor oil? Have you had good results? Is there any problem with oil heat expansion due to it be a heavier oil?
Hey guys I posted this over in the trailer forum but maybe some other triton owners could give me some info.
I have a 2004 Triton TR21x series with matching trailer with oil bath hubs. I believe...
Hey guys I have a 2004 Triton TR21x series with matching trailer with oil bath hubs. I believe they are the GOLD series hubs. I am planning on doing some maintenance before a long road trip due to...
Hey guys just bought a 2004 triton 21x series. I need to replace that motor guide with a minn Kota. I was curious what size shaft you all are running? I was thinking 52 but wanted to hear from you...
Hey guys I'm in search of a good nav/fishing map for the upper Chesapeake bay. What are your preferred paper maps that you use? I have a navionics chip for my units. Just looking for a quality paper...
Get ahold of Don at European Marine. They sell an entire block off kit with everything you will need. Recently did this with my 150xr6.
23 tempest it is. I run one on my 94 482v with a 150 xr6
Don,
while istalling my block off kit I have a quick question about the check valve where the oil line met the fuel line. Do I need to remove that valve and tee fitting and get a longer piece of...
:thumb up2: I'll give you guys a call today
Don
if I order the kit from you guys will it include all the items I will need to get it done? The plastic shaft, o ring, cover plate, screws, plug for crank case on starboard side, and anything...
I'm still undecided on how I want to handle this situation. Since the motor is older would you just recommend the block off kit or would you personally believe that it's worth paying that much money...
Worst case scenario here guys. After checking the whole system I decided to take the oil pump off and look for plastic around the gear. There was black shredded plastic all over the gear and inside...