I have a 2018 520c and was wondering if there was an easy way to bypass the interior light timer. Any help appreciated!!
Type: Posts; User: Capt Smith
I have a 2018 520c and was wondering if there was an easy way to bypass the interior light timer. Any help appreciated!!
My Fury 4 actually has 8 pvs holes. I’m running them all open. I always run the jack plate all the way up when I’m power loading. Both Fury load really well that way. Only the Razor has an issue with...
Both Fury power load great. Can’t get the Razor to power load at all.
2018 Z520C
250 Pro XS 2stroke torq master lower 1.75
poles
atlas hyd plate 8” setback
run 2.5 ptp but played with that a lot.
Jersey and the northeast so pretty close to sea level
5800 wot...
Maybe not. The three I drilled in the fury3 made a huge difference tho. I see on here that some guys do 5/16 holes on the fury3 and have to start plugging pvs holes. I really want to try and avoid...
I have a fury 3 25p that I ran on a 2018 z520c 250pro xs 2s. It was bad on hole shot and i was short on wot rpms. I replaced it with a fury 4 24p. Carries the load great put still sluggish out of the...
This prop just doesn't seem to be doing it for me. I finally got it to break over at about 3800 but she lugs real bad for few seconds before the RPMs come up and she takes off. Won't power load squat...
Ok guys. Thanks. I do currently add the quick clean and quick care every time I fuel up. I plan on staying with either the opti or dfi. I just wondered if it would jam me up if I had to use something...
The Merc dealer near me only carries the Mercury Optimax oil. I usually use the quicksilver dfi premium. He told me they are same oil. Getting the Optimax anywhere else around here is very hit or...
Ok, good. Would it be ok to mix some Lucas or Penzoil for instance? Or should I run the Opti oil and dump what is left before I switch?
Does anyone know if using an oil other than Optimax or Quicksilver DFI will void the warranty?
Yeah I have noticed that. Maybe it’s just as good as it’s gonna get. Got to admit, I’m little disappointed.
Depends on how I have it plugged. Wide open, no plugs, it turns about 4500 and never breaks over. With just the rear holes plugged solid, it takes about a mile to break over. The closest I had it to...
I am.
i do know that when I looked into a spare hub, it was the lower with the larger shaft. The Razor XL is a 24p so i cant imagine I'm over propped.
Its a 2018 and a torq master. Not sure if its gen 1 or gen 2 tho. I do know its 1.75:1. Either way I am a bit disappointed I cant seem to get it figured out.
Has anyone tried plugging the forward holes on the xl? I’m in a z520c 250 pro xs 2stroke.
tried several combos of plugs in the rear holes but still not getting a good hole shot. Been running about...
Yeah, I didn’t realize that the head unit IGPS was that accurate. I do get the heading on my one bow unit from the P1 on the stern so I think my current network is ok. I think I’m gonna take your...
I think you’ve explained my issue. The first P1 I installed, I connected to the existing backbone under the console. This new one I connected to a new backbone consisting of only the two graphs....
I installed a second point 1 on my bow. I only have it connected to my two bow units. For some I can’t seem to get either of the bow graphs to recognize it. I already disconnected them from the point...
2 stroke
Thanks for the replies. I guess you guys figured I was running merc
I am , a 250 pro xs with a 1.75 to 1 lower.
Has any one run both the bravo and razor? I’m in a 2018 Z520c. Twin power poles and lots of tackle. I’m turning a Fury3 25p. I only see 5500-5600 with a co-angler and tournament load. Hole shot is...
Will Mark respond to email or is it better to call? Anyone know that have dealt with him?
Is there any truth to it taking almost a year to receive a Razor from time of order?