Don't forget to fill the livewell and put 30lbs of bass in there too.
Type: Posts; User: Dharr
Don't forget to fill the livewell and put 30lbs of bass in there too.
Those are top speeds for sure and we tried a number of different props and jackplates but those boats look pretty empty and dry. I see posts all the time out with these speeds but jump up to our...
I haven't seen a 195 or a 198p out here run over 57mph empty. A 198p with poles loaded topped out at 48. The boat that broke all the welds ran 58 empty with a 2stroke but loaded with me in it as a co...
I have 195 with 115 pro xs. I run 48 tournament load in good conditions and break 50 by myself. Top speed was 52. The 150 tins in our club loaded run 48, 52 ,54 loaded and burn way more fuel. These...
I would say none of them. They are all good friends and baby their boats, there are days on the lake that you can't go 5 miles an hour without slamming down off a 4ft wake boat wave coming from all...
The way I see it... a factory with a bunch of employees welding aluminum, and mind you post covid employees which in every industry has seen a much different workforce, can and will have different...
Both 198p's in our club had hull failure one was the older design and one was the new bass pro design. Old failed in the keel ,new in the transom. The old one they won't warranty the new they did....
I did all of the 3yr maintenence on my 115proxs myself. Under an hour job. Drain the oil, while it's draining take care if the top end stuff. Drop the lowerunit change the impeller, put it back...
Bump
Looking to trade a almost new powertech nrs3 20p for a 19p x7 spitfire... prop has no dings or blemishes new last year. Been a good top speed prop I just run up a small river alot and without a...
Want to buy a spitfire x7 19p for 115 merc.
Mine slid off first time out hit the ramp bounced back up on the trailer and then slid into the water. Luckily the driver saw what was happening and didn't linger halfway down the ramp. It wasn't so...
I used plastic shoe totes with lockable lids for soft plastics and 3700 boxes for hard baits in the cooler. The cooler holds I think 7 3700 and 1 3600 on the side and it keeps all that weight in the...
My 18 doesn't have side rod lockers just the middle you'd have to cut the inside wall to allow for rods and that would probably hurt strength of the deck
Wondering if anyone can tell me if there is anyway to visually tell the difference between the old and new brush plate that changed somewhere around 2017. my boat is a 2018 and the motors serial...
Didn't see it there please pm me with price
Thanks
Didn't see it there please pm me with price
Thanks
I was thinking p touch but I was wanting a more permanent solution I know someone with a cricut machine and was going to mess around with that but im not sure how permanent that is going to be either
Wanting to replace the toggle switches on the dash on my 195txw with an easier to read rocker type switches. The switch isn't really the problem it's the engraved labels behind them on the panel...
I have the same prop you do and in the third hole I over Rev had to go to the 20p. Raising it one hole will do wonders and raise your rpms or go up to the third and put an x7 on it.
Water in the motor was the problem. A chip of the magnet ground itself up and eventually wore down a seal. Cleaned everything up and bought new seals it seems to be working fine. One of the contacts...
Pulled into some shallows yesterday and hit a small stick on half power and as soon as I hit it the motor stopped working. I pulled it up to replace the shear pin and all was good. Leaving it out I...
I would say something is wrong but multiple people have messed with it...jackplate,props, wedges..and there's another boat in our club with a 150 and he has the same results..there's also a few...
Mine runs 48 with two people loaded breaks 50 once in a while running a20p nrs3 prop. Not sure how much fuel I'm actually saving since running around at 40mph is almost wide open. I do know of...