Search:

Has anyone done any mods to a evinrude etec? I have a 40hp 2 cylinder I would like to get a little more out of.

1996 896 savage
1996 Mercury 200 EFI ( freshly rebuilt )
25p tempest plus work by MR. Andrew at lake lanier propeller
6" jackplate
3 1/4 PTP
18+ psi at WOT
5800 RPMs
full tank of fuel
2...

Thanks sounds good

Anyone?

How is the fury better than the tempest on your boat? Spees ? Lift ? And I hear that the fury's like to run a litter deeper than a tempest?

Has anyone tried a fury or a fury 4 on a heavy nitro. And how do they compare to the tempest? Thanks in advance

Ok. I installed a 6 in plate. I started at 3 1/2 below pad. Went up to 3 1/4 below pad all I can get is 65-67 depending on lake conditions. It will chine walk now but drivable still. Have I got all I...

Ok. I installed a 6 in plate. I started at 3 1/2 below pad. Went up to 3 1/4 below pad all I can get is 65-67 depending on lake conditions. It will chine walk now but drivable still. Have I got all I...

Ok. I installed a 6 in plate. I started at 3 1/2 below pad. Went up to 3 1/4 below pad all I can get is 65-67 depending on lake conditions. It will chine walk now but drivable still. Have I got all I...

This is the other number I think 835257q 6

Thank you. There is another number that end with i 6. Is that the same?

Can someone tell me the part # for a hub kit for a 96 Mercury 2.5l 200hp. I am running a tempest plus prop.

Ok thanks everyone for all the advice. I do have hydraulic steering so plenty of room there, just not sure about shift/ and throttle cables. I guess I will just go with a 6" plate. Either way I...

When I ran my prop stock, it ran 6100rpms and I could trim all the way up and toped out at 63. Now my prop is custom with more rake and extra cupping. Just fyi

This is what I can text you. I can keep bumping the trim till I get to 65 and if I bump it anymore​ I loose speed. But I also have a high rooster tail. My prop guy is telling me to go up on engine...

Well that's why I am trying to find out for sure. I had a friend tell me the more setback I can get the more lift I will get witch equals more speed. I don't always have extra cash to blow, so trying...

Will it be possible to get into the low 70s with a 6" plate?

Ok thank you. I really hope someone can tell me, because I would like to put a 8in on.

Ok right now my setup is no jack plate, prop to pad is 3 1/2 below. Running a custom 25.5 tempest plus prop. 3-4 seconds to plane and top speed is 65 at 5800. Looking for more speed so I have decided...

Ok thanks.

I get more bow lift without the hydrofoil. I had a buddy tell that it's giving me stern lift =more boat out of water/ less drag = more speed. And he said by going up on engine height will help. I...

Ok. Thanks. The crazy thing is that I can pick up 3-4 mph on top end if I use a hydrofoil. I don't understand that part. Right now it takes 3 1/2 sec to get on plane

Should I try moving it up 1 hole or 2?

I remeasured it today and it is 3 1/2 below pad. My prop guy is telling me I need to raise to engine up some, I should not need much trim, because my prop is lifting like crazy. Everyone I can find...

I remeasured it today and it is 3 1/2 below pad. My prop guy is telling me I need to raise to engine up some, I should not need much trim, because my prop is lifting like crazy. Everyone I can find...