Search:

Can 20.1 be loaded into a Ti2 and does the thing implode if loaded?

I tried to search this subject because I'm sure it's been covered but I guess I'm not tech savvy enough. I'm considering buying one of the Elite-9Ti units currently being sold by BassPro/Cabelas....

I have a new Elite 9Ti2. The unit came with an Installation Manual and a Quick Guide in a 6"x8" format. The box did not contain an Operator's Manual. I see there are a couple of websites where I can...

I have an Elite-7 with a HDI transducer available to connect to a trolling motor. If I buy another Elite unit that has chirp capability, will my HDI transducer be useable for chirp. I guess I can't...

Yep, I guess Yamaha has to get a cut for licensing that.

You can get the Yamaha logo when ordering from www.outboardcovers.com

I found it! Buried on the starboard side close to the rear latching mechanism. It has a cap on it that is stuck. I couldn't get the cap off and I'm thinking about using a heat gun to warm up the...

OK, thanks for the insights. It will be Monday before I can get back to the boat to recheck with renewed confidence that it's really there, somewhere LOL.

I do not have any electronic gauges, just analog volts and water pressure. I am updating the elctronics on my boat so I thought I would add the NMEA interface cable to my Yamaha so I would have some...

washers

Thanks Dutch Angler for your advice. I did buy an Elite-9Ti2 with the 3 in 1 transducer and a Point 1 antenna. Hopefully, I can use enough of the features and functions to justify the costs. Also...

I have an Elite-7 with a 83/200/455/800 transducer, works fine for me. However, I want to upgrade to an Elite-9Ti2. I don't know if my current transducer will work and/or which one of the transducers...

I have a 22ft Bay Champ that's been on a Hydro-Hoist lift for 5 years. I only use two bunks and they work just fine. I use the boat weekly. My only issue is spiders.

I have the 112# Riptide model, it did not come with a foot pedal. I love mine.

Are there other props besides the MinnKota props for a 112 Ultrex? I have two props and both vibrate. I have no confidence that a 3rd prop from MK would be better.

The thing about catalogs is that I buy a lot of stuff on impulse whether I need it or not.

Was the seat base installed with screws or somehow thru-bolted? I've been wanting to remove mine but the screws feel like they have a nut on the bottom.

I have a 2009 Champion 220 Bay. It's not your basic bass boat being a center console but it is a Champion. The fuel gauge is a standard analog Faria white gauge but on the back there is two 4-pin...

I will give a vote of confidence to Marelon fittings. They don't rust or discolor and they are virtually maintenance free. I'm not against bronze, stainless, or chrome over bronze, just saying white...

Actual plastic thru-hull fittings aren't good below waterline. They will age and snap the neck off from vibration, not good at all in the middle of a lake. Marelon looks similar to plastic, comes in...

My guess would be to the 220 and 240 Bay models.

I have a 2009 Champion 220 Bay with a 200hp Yamaha HPDI, it's not a pure bass boat like most on this forum have but it's what I like for a family fishing platform. My remote oil tank is stuck at the...

Use "Marelon" fittings. Some people think these are plastic but they are way better than traditional plastic, don't break and don't rust like stainless and don't turn green like bronze. Almost all...

^^^^Wise Advice^^^^^ It's sort of like remodeling every room in your house, sometimes it's better to just buy a new house that you like.

I'll post a couple of pics when I get some, thanks for info Lea.