Thanks for the info. Didn't have access to my engine to look this up, but now I know where to find it!
Type: Posts; User: GHolekamp
Thanks for the info. Didn't have access to my engine to look this up, but now I know where to find it!
I have a 2021 Mercury 250 Pro XS 4 stroke. (S/N 2B787656). I want to change spark plugs out as engine isn't running quite as sharp as in years past. Engine has just over 100 hours on it. What is...
I moved the vessel view module per European AM’s recommendation. Works perfectly now and I have no Bluetooth disconnection issues. Thanks so much for the helpful advice.
When the ignition key is "ON" but engine is not running, the module will activate and attempt to connect to the app. And yes, I have created a Vessel View account and reinstalled the app on my...
I have a 2021 Mercury 250 Pro XS 4 stroke. (S/N 2B787656). I installed a Vessel View module as per the instructions and successfully connected to it via the app using an iPhone X. It stays...
The Pro package has every option for a great fishing setup. I added the Atlas hydraulic jack plate for better running performance. The boat cover is of very high quality so consider adding that in. I...
Yes. The boat came that way from the factory. Boat and motor are brand new. 8 hrs on it. So are you suggesting I add one plug?
I am running with the hydraulic jack all the way down. All my tackle is also forward of the consoles. Not sure what else I can try. Maybe play with the jack settings more up ? At a loss for what...
Bryan, are you running a hydraulic jack plate as well? I have a 23p Fury on my 2021 Z21 (250 ProXS/Atlas hydraulic jack) and it always wants to porpoise after getting on step if I want to go slow at...
Thanks. It’s odd that the package has a different model number. 8M0115080. Tried to attach a photo but can’t seem to make that work.
I have a 2021 Mercury ProXS 250 4 stroke. (S/N 2B787656). I wanted to install a Vessel View module. Is there just one model of Vessel View or is there different ones for different engines? So far,...
Isn't the point of a transom saver to take the pressure off the transom and onto the trailer when towing? The products mentioned in this post do not accomplish that, but will take pressure off the...
Sounds like it is missing the stop. My 2021 Z21 Pro doesn't do that. On another note, check your seat posts to make sure they actually screw into the bases. Both my front bases were too deep and the...
Premier Boating Center in Jasper, TX.
To answer the other question, it is a pedestal issue mounted in the front deck. Both are 1/4” deeper than the base mounted in the rear deck. Pedestal pin...
Does anyone have a contact with a supervisor at the Nitro factory? I could really use some help getting some attention in getting this resolved. Bryan McDonough - can you help?
This is still dragging on. The dealer has been communicating with Nitro but still no solution. I called Nitro directly and they told me I needed to work with the dealer. The last recommendation was...
Oil level is good and within recommended limits. Will try the engine trim idea when shut down. Sounds odd to me to have oil get past the rings just because the engine is completely vertical. That...
I have a new 2021 Mercury 250 Pro XS 4 stroke. (S/N 2B787656). Still in the break in period with about 5 hours on the motor now. Following the owners manual for break in procedure. Noticed today...
Pin is 4”. The female insert is 4.5” deep. Pin won’t reach. I think Ntro got a bad batch of bases. My guess anyway. No easy fix however unless you rip out the carpet in a brand new boat from the...
I just picked up my brand new 2021 Z21 and the piston seat pedestal (made by Springfield) will not screw into the base on either hole in the front deck. It appears to be almost an inch too short to...
ok....so I bought a replacement voltage regulator. Are there any tricks to replacing it or is it pretty straightforward on this engine? Hoping I don't have to take a bunch of things off the motor...
I had the same question. My boat is up at Sam Rayburn and I don't have access to look at it now. Can someone answer where the 2 regulators are located on this engine? Thanks!
if I am understanding correctly, there are 2 voltage regulators on this engine. I would assume only one of them drives the tachometer so the other voltage regulator would not have the gray wire...
I have a 1995 Mercury 150 HP XRI. S/N OG282494 on a '95 Nitro 190DC boat. Over the past year, my tachometer has intermittently worked. The higher the RPM the more likely it would just quit and drop...