My 2003 187 measurement of trailer bunks is 77 and 125 inches length.
This is just over 6 feet and just over 10 foot, I am measuring from tip to tip of the total bunk with the carpet in place.
I...
Type: Posts; User: Daf290
My 2003 187 measurement of trailer bunks is 77 and 125 inches length.
This is just over 6 feet and just over 10 foot, I am measuring from tip to tip of the total bunk with the carpet in place.
I...
Never mind! I played with it some more and even though I could easily put a pipe cleaner all the way through the tubing was somehow clogged. Removed clogged tubing and all is well.
Thanks BBC
I need help on next steps.
my 2000 V150 (2 stroke), stopped peeing, the pee hose is clean and clear but no discharge with flush hose running and motor both off and at idle.
all previous times...
My trailer has 4 bunk boards, I am considering replacing two with Gatorback clear and led lights and two with the Ultimate PVC boards.
Do you think this is problematic?
I believe that they are...
Yamaha with Mercury prop thrust washer difference
I have a 2000 Yamaha 150 V model (2stroke) with a Mercury Tempest Plus prop. I have a new hub kit and the thrust washer is different between old and...
This is the hub kit that I have, I believe it’s correct. I am still not sure if I should use the old or new thrust washer
not actually certain what the thrust washer is designed to do? Only support...
I have a 2000 Yamaha 150 VTLR model (2stroke) with a Mercury Tempest Plus prop. I have a new hub kit and the thrust washer is different between old and new, the old one is flat against the motor...
Ha, nice photo but luckily not my boat
great to see it didn’t roll over though
I have a 2003 187 and although I have about 80 hours in the driver’s seat mostly on Lake Erie I consider myself a novice driver.
On Erie last week I got into 4 foot plus with a very short frequency,...
Marc,
thanks that worked great!
I have tried for an hour and can’t make my pages go from a split screen to single screen display.
I can split and unsplit each side separately and I can reduce the unwanted screen to small but not...
I have an old Fluke meter and it doesn’t appear to have the ability to measure frequency
It appears that I am getting signal from the motor as the tach certainly responds to the motor
if I get a...
Some say that fixes the problem
I believe that it reduces the signal amplitude but not certain.
I tried many different resistors with no real change
10k ohms is what’s recommended.
I am hoping...
I bought a cheap Chinese tach and can’t seem to make it work. I’m sure that I have the tach settings correct and have tried many resistor combinations wo success. Placing a 10k or other resistor in...
I bought a 2003 187 a year and a half ago from Eastern Ohio original owner with a 150 Yamaha 2 stroke. My first bass boat and I absolutely love it... Most of my outings are alone or with one other...
I am installing a new Carbon 12 inch and in replacement of the transducer I find this old sensor that was attached close to the old transponder.
I have tried to trace the wire up front but I believe...
OK, Last question,,,
I currently have mounted on my TM a transducer from a Lowrance Elite 5 DSI, the specs of the transponder are copied below. Just use this transponder?
Transducer
Skimmer®...
Sorry for my ignorance
I believe that the transducer with the gen 2 is called LSS, that’s what I meant not 3 in 1.
Is there a benefit to use the LSS transducer vs the skimmer, vs the even older...
I understand and very much appreciate your comments
my only question is why not use the older 3 in 1 and the structure scan on the trolling motor?
I would believe that I can rig the wiring and...
So my best bet is separate systems new in back and old in front,,?
Thanks!
I Just got a Carbon 12 with transducer and need to take my existing Gen 2 (I think) HDS 10 to the bow TM and install the new Carbon.
I have both the skimmer and "conventional" full size transducer...
Thanks
just finished ordering it….
I have a 19 ft Champion with a gen 2 HDS 10 at the console, I am considering buying the Bass Pro Black Friday Carbon 12 to replace my current and move the Gen 2 to the bow replacing the current 9...
I got last fall a 187 with Yamaha 150 and hydraulic jackplate.
I’m spending more time on Lake Erie and can get into bigger water.
i have never been close to submarining a wave but take many over...
Rat,
Did you resolve your tach issue?
I have an aftermarket tach on my 2000 F150 Yamaha and am having issues similar to yours
thanks