I just got a brand new 2018....and Have a deep scratch from point of bow to U bolt already. about 5th time putting it on trailer the nose landed inbetween the outer and inner section of...
Type: Posts; User: Radar19871
I just got a brand new 2018....and Have a deep scratch from point of bow to U bolt already. about 5th time putting it on trailer the nose landed inbetween the outer and inner section of...
Was just at dealer comparing these two..to my suprise we measured from bow shroud to edge of center locker. I dont remember the actual measurement bur 920 actually had 3-4 more inches of useable deck...
I can use the navigation chart Todd, but they have stripped away my ability to use depth shading. Basically my favorite feature. Now I have to look at a plain yellow lake with contour lines. There...
Thank you Larry.
So does this make my Ultra 2016 card no functioning seeing as I already updated it before the 2017 maps released? What a way to make a guy purchase a new card.
So I updated 7612s and 7610 to 9.20
Now I cannot get my depth shading to work...I click on fishing chart, and the depth shading is there....but no contour lines. I call Garmin support on the...
I have the exact same results as you puhlw....i'd just like to know why the theory is not a reality. If I turn the brightness to high on 800 it just clutters up too much. But if I lower to remove...
Does anybody run their DI or SI on 800kHz with good results?
I can't seem to get a good picture running 800kHz, I have messed with every setting I can. It would seem the Higher frequency...
http://www.bbcboards.net/attachment.php?attachmentid=251238&stc=1
Anyone know if I can change the color profile for the boat lanes.. On Toledo Bend the boat lane being a black dashed line is super helpful, but hard to pick out from the rest of the chart when you...
I have a PS30 and 31 on my boat. I kinda wish I would have gone with the 21 instead of the 31.... The built in heading sensor would be great for lining up on my waypoints when the wind in blowing...
If I arrive at a lake, and adjust my Lake level. Then go chart some area's using quickdraw. Does the topography I made automatically get scaled to the lake level I had set? or do I have to remember...
Is there a way to Highlight certain depth's? or just a quick way to spot certain depth's, without having to hover the mouse everywhere?
Got a new 25p FXP and sent to Mark, Boy does it launch out of the hole. So turns out I believe my Tach is off. I hit 74mph in about 90* air temp. my Tach was showing 5200rpm. boy it gets to 74...
So are you dropping the lower unit on every oil change? And are you just greasing the shaft?
Thats pretty disheartening Dawg.....why brag about our quiet engines when they sit there and drive you nuts with queaking at idle.
Is there any way to get the Timber cuts on the Northern end of Sam Rayburn into our units?
When did this change, I just got my card, and had to buy the FHS update separately.
I thought It sounded like a belt as well, but I looked over my belts and they all still looked brand new to me. I think skeetRJ might be onto something, I was going to do a Oil change this week so I...
I can't seem to get going that fast without causing to much prop wash/ interference.
Hey Guys, I have a 2014 SHO 250, Has devoloped a squealing/ squeaking noise After it is ran hard and idling. it normally only occurs after a long hard run, then when I drop back down to idle it...
Hey Guys,
Was wondering if anybody has added any goodies to their ZX20? Was thinking it wouldn't be too hard to add like the measuring board slot and tool holders to make it more like an FX. ...
Also performing updates will be much less time consuming with them ether net linked, as all units/transducers will update together.
And no, you will not get a Transducer reading without your vessel being in the water. You may hear them ticking, but if you get anything on the screen at all it will only be "noise".
I would use a network cable for linking your units rather than the NMEA2000 Bus.
Hey Guys,
I seen some of you guys got docks to overlay on your charts, I have my Detail set to most and cannot seem to get this to happen on my unit.
I have the 2016 Ultra charts and all my...