HumminbirdPC has been updated at least three times, 2018, 2019, 2020. I have the software downloads of those three times.
I think most of those were adding the capability to open different file...
Type: Posts; User: Wayne P.
HumminbirdPC has been updated at least three times, 2018, 2019, 2020. I have the software downloads of those three times.
I think most of those were adding the capability to open different file...
DSC stands for Dual Spectrum CHIRP and with Humminbirds, it is 140-240 kHz or High Wide CHIRP using a Low-Q CHIRP rated piezo.
It is called Dual Spectrum because Humminbirds have three choices...
If Heading is screwing up, it's probably because the Heading Sensor (compass) is not installed correctly.
Heading is done via Heading Sensor and has an orange Heading Line when turned on.
The...
Yes, BUT heading is mostly useful when GPS cannot calculate direction (like when fishing at the bow using the trolling motor). Typically at the console you are moving faster than .6mph and will have...
No, it just happens if the Ethernet connection is functioning. You do have to select the other unit in the Sonar Source menu for 360 if it is not highllghted.
This is a G1 networked to a G3 with...
Advanced GPS/Heading is turned off when the motor is stowed. The motor has to be deployed and powered to use it.
The Minnkota heading sensor has always been Bluetooth. It "talks" to the iPilot/Advanced GPS via Bluetooth and can only be shared to a display via Ethernet.
The Humminbird AS GPS HS (combo...
You can use the Minnkota Heading Sensor with a display if it is iPilot LINK or Advanced GPS. It's an Ethernet connection.
Two things are needed for the MDI transducer and a Helix 7 MDI.
MKR-MDI-2 adapter.
Connected Transducer setting==Built-in HW+MDI
Manual page 85-------One-Boat Network App Operations Guide (widen.net)
Nothing is changed when using a Y cable with two transducers. The only change is the physical location of the function that is split off. In your case it should be the 2D piezo in the "other"...
The settings have not been changed. Their effects have varied since the beginning.
Just do a web search for MEGA LIVE settings and find a video that shows what you want to know==there are dozens...
Do the units have the same version software?
The only way to know is by using it. I had two that had mfg dates close to each other, one was defective and the other wasn't.
https://youtu.be/ev3wxctWsgQ
https://youtu.be/-2WmMyUc06I
It was the Oct 5 2023 software that exposed the defect--2.890
Current software 2.930 was released Feb 8, 2024
Yes, it is stated on the Humminbird website for that accessory in the Features section.
No, the 2.930 software does not support the 360.
Units older than G3N don't get software version 2.930 so your 360 is not affected using those.
That is 6 network devices. To have more than 5 requires two Ethernet Switches.
Connect the two Ethernet Switches with an Ethernet cable, which gives you 4 Ethernet ports on each Switch to connect...
Yes Humminbirds read Navionics map products. The ContourXD mapping built in is Navionics 2006 data.
What does sending in the unit for repair have to do with a map card?
Yes, disconnect the cables from the Target Lock, remove the Heading Sensor, unbolt the LIVE from the Landscape ratchet and pull the cables out.
You need to provide three things for them to...
Must not be working if you did the calibrations, have the correct parts and don't have the Minnkota Steer function.
If you did all the steps as they are stated in the instructions and your devices...
Read this thread:
Mega Live transducer defect revealed? (bbcboards.net)
If the interference looks like this, it is that:
https://i.postimg.cc/G90mdWDb/RFIa.png