thanks for the info
Type: Posts; User: barnyard
thanks for the info
i am looking for a transducer that has side and down scan
I INSTALLED 18.2 TODAY SEEMS TO BE KEEPING TIME CORRECTLY. IN THE UPGRADE DOES ALL IN BETWEEN UPGRADES BETWEEN 7 AND 18 COME WITH 18?
OK, I will do that
i have version 7
HDS-GEN-3 will not keep correct time. I HAVE RESET IT MANY TIMES, BUT IT STOPS WHEN NO POWER IS CONNECTED.i
i fished yesterday, it didnt start at first but after it started the first time, it worked good all the rest of the day. hard to find a problem when it changes off and on.
I accidentally left the switch on last nite and today it seems to have repaired itself. I hope to run it tomorrow and check it out. I don't know why. I also don't have a transom mounted key switch...
I checked for spark today, no spark. If I switch it off and back on it has spark. also I noticed no warning horn at first. then after switching off and back on the alarm sounds. maybe i need to take...
yes the motor is spinning
the starter is spinning, but the engine doesn't start un til i press the starter several times. I can hold the start button and the starter spins as long as I hold it. If I press the stop button then...
i can hear the fuel pumps running, but i haven't checked spark. i really don't think spark is a problem because it runs fine once it starts but i will check the spark tommorrow. thanks for the advice.
yes, i always pump before launching
ser. ot674103 I HAVE PUSH BUTTON PANEL WHEN I PRESS THE START BUTTON THE STARTER CRANKS THE ENGINE FINE, IT HAS ALWAYS STARTED IMMEDIATELY BUT NOW I HAVE TO PRESS 2 OR 3 OR 4 TIMES BEFORE IT STARTS....
thanks for the info, I will check to see if I can determine if that is the problem.
ser. ot674103 I have never had a problem with starting this engine. Now when I press the start button, ranger 519, it just spins the starter, then if I release and press again it starts like normal....
i found my problem, operator error. the kill switch was off. dumb mistake!!!
i have a 200 opti ser.#ot674103 when i press start button the warning horn does not chirp. i have checked the horn with separate battery, it worked fine. is the problem in the computer? i checked...
reeds have always been replaced with stock reeds by my dealer
I have a 2003 200hp optimax ser#ot674103 I BOUGHT it from a friend in 2005 since then it has broken reed valves every 2 or 3 years Is there a cure for this problem I WOULD like a good remedy...
I FOUND THE PROBLEM, THERE WAS A BARE SPOT ON THE TEMP SENSOR. I HAVENT RUN IT YET ,BUT IM PRETTY SURE AFTER I TAPE UP THE WIRE IT WILL BE OK. THANKS FOR YOUR HELP, DON.
150 XR6 SER# 1B042528 THE WARNING HORN BEEPS ONLY WHEN CROSSING ROUGH WATER. IT NEVER BEEPS WHEN RUNNING ON CALM WATER. THE OIL TANK ON THE MOTOR IS FULL,AND THE LARGE TANK INSIDE THE BOAT IS OVER...
OK GUYS CALL ME A DUMMY. I FOUND THE PROBLEM. IT WAS A STOPPED UP FUEL LINE BETWEEN THE BULB AND THE ENGINE. DONT LAUGH TO HARD BECAUSE I REPLACED THE LINES LAST YEAR WITH THE GREY LINES AND BLUE...
THERE WAS NO HOLES IN THE DIAPHRAM. THE # I GAVE IS THE # ON THE PACKAGE THE KIT CAME IN. THANKS DON FOR YOUR HELP.
IT WAS A MERCURY KIT #42909A4/21-857005A1 NO DEBRIS IN THE PUMP,, ALL LINES AND BULB WERE REPLACED, NOT TO MENTION IT RAN FINE TWO DAYS BEFORE. ALL ARROWS ARE IN SAME POSITION. I WILL CHECK BULB...