Search:

Type: Posts; User: Ebuck155

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    2,792

    I have a different set up, 1989 Merc 200 XRI, and...

    I have a different set up, 1989 Merc 200 XRI, and I had power to my gauges, turned out to be my voltage regulator going bad. Just a shot in the dark for ya.

    tdt91 why reply when you don’t know,...
  2. Went with the CDI. Works great now. Thanks...

    Went with the CDI. Works great now.

    Thanks
    Eric
  3. Its in the shop, its the voltage regulator....

    Its in the shop, its the voltage regulator. Everything has been tested and is good
  4. I called Western Marine and they said Sierra...

    I called Western Marine and they said Sierra didnt make a 40amp regulator. He even called Mercury to cross reference numbers and they didnt have any.
  5. Thanks, CDI makes a 40amp direct replacement, no...

    Thanks, CDI makes a 40amp direct replacement, no need to do anything with stator. Its about $200 bux cheaper than OEM. But any issues with CDI?
  6. 1989 Mercury 200XRI Money Pit Begins!! Volt Reg Needed!!

    Well, after 2 hrs on the water voltage regulator fried. Its at the shop now and was told $700 just for Regulator, OEM. Are there any other options, aftermarket out there? This things is starting to...
  7. Replies
    6
    Views
    1,313

    Hmmmmmm, I suppose I could try that, I was very...

    Hmmmmmm, I suppose I could try that, I was very careful assembling it. But you never know.

    Thanks
  8. Replies
    6
    Views
    1,313

    Both brand new and inspected before install. ...

    Both brand new and inspected before install. Weep hole is for high pressure release.
  9. Replies
    6
    Views
    1,313

    Poppet Valve Leaking Still!!

    Ok, so i have this 1989 Mercury 200 XRI Serial #0C157845. I have replaced the water pump (impeller, gaskets, o rings, housing etc. and I just did a rebuild kit on the poppet valve ( everything in...
  10. Replies
    6
    Views
    378

    He said it was a Bridgeport.

    He said it was a Bridgeport.
  11. Replies
    6
    Views
    378

    [Thanks

    [Thanks
  12. Replies
    6
    Views
    378

    He said it could be a 3.0 also, he didn't know.

    He said it could be a 3.0 also, he didn't know.
  13. Replies
    6
    Views
    378

    '88-'89 Race Merc 2.4?

    So I came across a Mercury that has had some work done to it, but not sure exactly what it is. The serial number is A953330. It sits on a '19 Action Marine.

    Any ideas on this Engine based on...
  14. Replies
    1
    Views
    172

    89 200 XRI Poppet

    Well apparently i need a poppet valve, or rebuild kit. It failed today and psi was erratic and over heated at times, but not to failure, uggggggg. Any ideas for replacements?

    Thanks
    Eric
  15. Replies
    10
    Views
    588

    Well apparently i need a poppet valve, or rebuild...

    Well apparently i need a poppet valve, or rebuild kit. It failed today and psi was erratic and over heated at times, but not to failure, uggggggg. Any ideas for replacements?

    Thanks
    Eric
  16. Replies
    10
    Views
    588

    Thanks Euro.. Wow I would have figured that parts...

    Thanks Euro.. Wow I would have figured that parts were a dime a dozen. anything I should look for and stock up on, just in case?

    Thanks
    Eric
  17. Replies
    10
    Views
    588

    :popcorn:

    :popcorn:
  18. Replies
    10
    Views
    588

    OC157845, Why do you ask?

    OC157845, Why do you ask?
  19. Replies
    10
    Views
    588

    European AM, I am guessing you will know this...

    European AM, I am guessing you will know this engine, I believe it came from Greenville as did the boat. I will see if I can get it from him.
  20. Replies
    10
    Views
    588

    Oh yea, and best prop for it. It will be on a...

    Oh yea, and best prop for it. It will be on a 1988 20' Shadow. Looking for fully loaded and about 450 plus driver/passenger weight and a good start for P tp P height.

    Thaks
    Eric
  21. Replies
    10
    Views
    588

    1989 200 XRI EFI Input

    Hello Merc world. I have a chance to get a great running, very well maintained 89 200 XRI. Was/is there any issues with these engines to be weary of?

    Thanks
    Eric
  22. Replies
    15
    Views
    406

    Update.. went with the 3/8" hose, set the...

    Update.. went with the 3/8" hose, set the throttle arm as manual says, didnt syn n link yet, throttle blades now open to 90 degrees and took it out. Runs great, course it always has. I picked up 200...
  23. Replies
    16
    Views
    841

    Thanks td91. Yeap the sleeve was not on there....

    Thanks td91. Yeap the sleeve was not on there. Championman, as well as others, has been a huge help. I posted up on the Evinrude/Johnson forum and got some great advice.

    Thanks again
    Eric
  24. Replies
    15
    Views
    406

    Awesome thanks Championman, and everyone...

    Awesome thanks Championman, and everyone else!!!!!

    Eric
  25. Replies
    15
    Views
    406

    Ok Ive been looking through the manuals and I...

    Ok Ive been looking through the manuals and I cant find 1 with my Mod #. VJ175SLESE. Will this one work?

    1990 Johnson Evinrude "ES" Cross V 88 thru 115, 150 thru 175, P/N 507874
Results 1 to 25 of 45
Page 1 of 2 1 2