Mine kept loosening until I double nutted it.
Type: Posts; User: Ranger519VS
Mine kept loosening until I double nutted it.
I would think if you are replacing seals the spindle sleeve would have to be part of it to ensure you are not going to have to do it again anytime soon.
Should already have a hole in the corner of the Transom brace plate. That is the wall on the right side of the starting battery compartment. Hole is in the lower rear corner. There may be trash...
check this out:...
You could try calling Dexter to see if they have parts but as you can see they have superseded the 19 year old model you have. If it were me I would replace the whole thing as all the parts are well...
If there is a hose on the gauge then you don't have the remote transmitter. Its purpose was to keep water out of the gauge. You'll have to get a new gauge. Is your gauge one of the Ranger branded...
A 9' door would work with inches to spare. Personally, I would want a 12' door minimum.
Yep, the gauge is toast. Are you sure the tubing goes all the way to the gauge. Most boats that era had a remote pressure transmitter. It look like a small cylinder with the water pressure hose...
Here is just one source I found on the internet for an example. Many companies sell parts for them. You may not need the whole master cylinder but its a lot cheaper at $250 than buying the whole...
If they made trucks with hoods you could see over, you wouldn't need the sensors to tell you when you are getting too close. My pet peeve with pickup trucks. Lots of room in the engine compartment....
I regularly get emails from St Croix about their sales and they have never offered their “retired “ rods for less than a 10% discount off list
I have been running a Fury 4 for about 5 years now on my Z521 Ranger SHO with no problems. I spoke with a well known prop man recently about sending it to him to tune it up. He expressed surprise...
I have 2 12 Lives and I had the same issue with not sharing waypoints and not sharing Navionics map. Turns out they were not communicating with each other on the ethernet line. New ethernet cable...
There has been a continuing problem with Lives networking together since the latest firmware updates. Lowrance supplied me with a NEP-2 network hub for free to cure problems with my Lives not...
I'm a little late to this thread but I have been running 3-Dakota Lithium 50A batteries in series for my Ghost trolling motor for the last 3 or 4 years with no problems. I added a Victron smartshunt...
Hopefully got my issue resolved this afternoon. I was unaware of other discussions of this same issue that others were having since I am not a regular reader of this forum. Contacted Lowrance...
Yes, I did a soft and then a hard reset. I bought them last December when they released the Pro and dropped the asking price on the Lives. They had been working fine for a while (I think) but I...
I have 2 HDS Live 12 units. One at bow and one at console. Having an ongoing problem with not sharing waypoints or maps. Everyone says its an ethernet problem. Installed new ethernet cable. ...
I am helping a friend who has 2 Helix 10 units. I am not familiar with Humminbird units and there waypoint management.
We want to sort some 7000 waypoints by lake and have separate waypoint...
I bought one from Ranger about 4 years ago for my 521 and it was about $600 including freight. That was just the axle. They said 4 weeks but it arrived a week later. Should have replaced both of...
Had this issue with my 2011 521. Turns out the bushing in the tilt shaft was bad on one side. That was o n a SHO with the cheap nylon bushings Yamaha uses
I had one similar to that shown. It had been on for a long time and was rusted in place when I tried to remove it. I usually put my hitch on in the spring and remove in the fall.
I have used the u...
I have the Dewalt and can highly recommend. It’s a Beast
Those same factors (headwind/tailwind, uphill/downhill) affect ice vehicles also in the exact same way.
yes, advisers say it all the time.