Search:

It's about 100 ft of steep elevation drop from house to water. Lugging 4 batterries to the house isn't going to happen. The power station weighs 6 lbs and is the size of a lunchbox. It's a unique 1...

Looking to get a portable power station to charge trolling motor batteries. We'll be staying somewhere that has power at house but not at dock and dock is too far away to run drop cord. Any concerns...

Leesburg Landing most of the time.

Thanks for the info, that'll give us something to start on. We'll be there for a week so we'll take our time getting around.

Going to be fishing at Weiss for a week in late October. Never been there before, any hints, tips clues for bass fishing? Patterns, navigation, general areas, etc. Not looking for GPS coordinates,...

Not familiar with that model, but could it be hitting rev limiter? I've had a few outboards that would "bump" when they hit redline.

Thanks, I'll mess around with it a little more next time out.

I mounted it on the trolling motor shaft, it appears to be straight and the I calibrated the transducer. Only been on the water once since I installed it. Will go through everything again when I get...

Everything I've read online and on the manual says to put the unit in "auto" when changing transducer orientation. I still have to manually set it for the mode I'm operating in (down, forward, etc). ...

I have one that runs across the top of the passenger side gunwale. Looks like it starts at the cup holder on the inside gunwale wall. (I think this covers and access point to install a modular...

Make sure all of the carpet is fastened down, pay special attention to vertical section from under the seats to the floor and inside the rod lockers.

Maybe vice grips and if you need extra leverage, an extension bar or pipe. As others have suggested, probably change them all.

I'd be leery about buying any car, truck, boat, outboard or RV that's been built from spring of 2020 at least thru the end of 2021. High demand for outdoor products, vehicles, boats and other marine...

The gauge shows 8.01 mm from bottom of head to bottom of screw. For the metrically challenged, that's about .31 inches.....so yes, it's "around" 1/4 inch.

I had the same boat/motor combo back in 1999. If I recall, I was running a 24 Raker.(3 blade) (not sure what is available now) I could get a little over 72 mph with a tournament load on a cool day....

What motor?

True story: Yesterday I was fishing around a GA state park campground at about 730 and some guy pulled out a leaf blower and started blowing off his campsite. He had neighbors on both sides.

Not saying this is the cause, but if you hit the on/off button it will dim the display by about 1/3 each time, then on the next press it will bring it back on the 4th (or something like that). On the...

Probably should include serial numbers as well. They are usually sequential and you may be able to identify a bad lot or run.

Clearly, this installation was poorly executed. He didn't even use duct tape.

Best I have is "probably". Not familiar with this particular transducer, but in general, the plastic casing is just that. The actual sensor is inside. However, the cracks could great some...

Look around the rim of the lower cowling for missing bolts. I had a few of the bolts that hold the clips that hold some of the cable clips (I think) work loose. One fell completely out and was...

If the park is full, you might check on Air BnB or VRBO. Sometimes they're as cheap as a hotel and better for parking. If you're spitting with other anglers, it can be a pretty good deal.

I get it on my 919 under certain conditions. As Zpage stated, I think it's the wind between the windshield and console. I was going to try putting some weather stripping in the gap to see if that...

I created a screen with side scan right only on right panel and left only on left panel. Down scan and chart in the center. When I go back to that screen, the left side shows side scan in both...