The nose actually sticks out farther than the tongue pivot point - the measurement is 24’11” with motor trimmed up - subtract 15” if trimmed down- mine is a 2017
Type: Posts; User: Billbobclark
The nose actually sticks out farther than the tongue pivot point - the measurement is 24’11” with motor trimmed up - subtract 15” if trimmed down- mine is a 2017
Actually the higher gunnels are an advantage. When your rods are strapped down and you have to get into the compartment under the rods then the rods stay in the boat and don’t hang over the edge -...
About 4 inches at its tallest but around 3.5 where the seat is
How tall are you ? I’m 5’11 and flip/pitch with a 7’+ rod - no problem. If I remember I’ll measure when I get home
Padding for sure - have it on my Phoenix and when i redid my aluminum boats carpet i padded it - buy closed cell foam - no problem drying out
Not sure about the 2014 - I have a 2017 921PHX- I liked what I saw on the new models ( especially the foot switches for the trim )but they weren’t available for mine - I called them up and they made...
Can you have the holes welded ? What I mean is - close up the holes a bit with weld and then re-drill the holes to proper size - sounds like the “pin” holes have become enlongated ?
I don’t think you would need to dim them- the picture is a little misleading. They are plenty bright for your deck but not so bright that you would need to dim them
https://www.amazon.com/gp/aw/d/B01H7FGO46/ref=sspa_mw_detail_5?ie=UTF8&psc=1&pd_rd_i=B01H7FGO46p13NParams
I used these- ran all the wires to a separate fuse box then I ran a power and negative wire...
I lined my cooler with “dynamat “. It’s closed foam insulation used in hot rods to keep heat out of the cockpit. Get the thermal stuff and not the sound deadening stuff- I also replaced the factory...
Something to think about - I paint cars - flat and satin cars are popular. BUT you cannot buff out a problem- it becomes shiny ! Maybe gel coat is different - I don’t know. I do know that on my shiny...
I had a carpet cleaning service guy tell me that using soap on your carpet is bad - he said use just hot water for best results . If you do not get all the soap out then the residue from the soap...
77-78 inches
https://www.dynamat.com/products/dynaliner/
lined my cooler with this - huge difference . Use the heat insulator stuff . Used on firewalls of hot rods to keep the heat out of the passenger...
this 👍
I recommend looking at the specs/measurements of the front deck . I REALLY like the extra width in the 900 series. I have the 21 PHX and I have a ton of room up front with no worries about stepping...
:thumb up2:
Outside tire to outside tire = 99 inches...and in case you’re wondering- the fenders are flush with the tire so 99 inches is max width
I have 10’s and I’m happy with them - garage door height is a factor though - keep the remote in the truck with me to lower a bit when in and out of the garage - hope I don’t forget some day !
I would bet you can get some large bushings that you could take the slop out of the holes - old car hinges are repaired that way
Registered Nurse at the VA and restore/build classic cars/hot rods as side job
I bought a kitchen drawer handle type pull- a little larger though- mounted it inside my boat by my throttle- it’s chrome- looks factory- and I just clip them to that and they hang there next to my...
A club member recommended Optima yellow tops to me after he got 7 years out of his ! They’re only 75 ah though - anyway I have had them 3 years (minn Kota fortrex 112)- 21 foot boat. Just fished a...
Ha ! Easy .... didn’t think of that
Not sure what factory uses but I would use a 2 part epoxy paint