Search:

Type: Posts; User: thommo59

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    67
    Views
    2,390

    Try the coastal flush on the side and give it a...

    Try the coastal flush on the side and give it a good flush without the engine running
  2. Replies
    10
    Views
    695

    This type of crack seems to be coming more common...

    This type of crack seems to be coming more common in exactly that same place
  3. Replies
    25
    Views
    1,856

    It got worse for me, hds live 12 and AT2 and...

    It got worse for me, hds live 12 and AT2 and since the latest update I’m lucky to get an hour without the dreaded no source. Drove me crazy today, I wonder if the placement of the black box and how...
  4. Replies
    7
    Views
    493

    Mine goes in through the flexible grommet /...

    Mine goes in through the flexible grommet / flange and that has cable ties around it to seal and hold the rigging tube. The rigging tube is long enough to enable lock to lock steering without pulling...
  5. Replies
    3
    Views
    280

    Thanks it seems that android works well but apple...

    Thanks it seems that android works well but apple no so much, I’ve tried an adaptor but it was rubbish. Works fine on my TV but not on the HDS
  6. Replies
    3
    Views
    280

    HDS 12 LIVE Viewing Live Stream

    I bought a HDMI converter to plug into my Live 12 do I can watch some sports on the screen via my IPhone. It all connects fine, eventually shows like a tiny bit or just 1 second then it’s gone. Can...
  7. Replies
    7
    Views
    412

    Start at the waterpump

    Start at the waterpump
  8. Thread: lower unit

    by thommo59
    Replies
    18
    Views
    1,421

    Has your stance changed on this Don? There were...

    Has your stance changed on this Don? There were posts a year or 2 back where you suggested not to do this but only use the level fill method until it trickled out
  9. Where that bolt goes in there is a cross pin with...

    Where that bolt goes in there is a cross pin with a machined dimple in it. The bolt must fit into that dimple for alignment. The fact you turned it half a turn is now a problem for 1 it shouldn’t...
  10. Replies
    6
    Views
    467

    Don’t trust your lowrance they are notoriously...

    Don’t trust your lowrance they are notoriously bad for voltage readings
  11. My guess is they would like to analyse the full “...

    My guess is they would like to analyse the full “ run file” and this is downloaded via the Merc g3 system. I’m guessing this dealer doesn’t have or needs a new harness to perform this
  12. Replies
    30
    Views
    1,668

    I don’t know the number sorry but Don will also...

    I don’t know the number sorry but Don will also tell you the correct torque sequence that also makes a difference
  13. Replies
    30
    Views
    1,668

    I understand, it’s a brass nylock nut, the nylon...

    I understand, it’s a brass nylock nut, the nylon eventually wears and it’s time for a new one
  14. Replies
    30
    Views
    1,668

    I think it’s time for a new prop but, the nylock...

    I think it’s time for a new prop but, the nylock is not really intended for ongoing re use particularly where heat can be a factor
  15. Thread: TPS issue?

    by thommo59
    Replies
    3
    Views
    247

    The TPS Throttle Position Sensor won’t have...

    The TPS Throttle Position Sensor won’t have anything to do with the shift unless you have your foot on the pedal and raising rpm’s when you shift. I’m sure Don will chime in but essentially it...
  16. Thread: 300HR service

    by thommo59
    Replies
    20
    Views
    941

    Think yourself lucky you could get an oil filter,...

    Think yourself lucky you could get an oil filter, here in Australia they are a 2 month wait
  17. Replies
    6
    Views
    284

    It’s the bolt that holds your trim pin in place,...

    It’s the bolt that holds your trim pin in place, don’t try to run the engine without it. This is located at the underside of the engine at the top of the tilt ram. Tilt engine up and you’ll see where...
  18. Thread: RPM issue ?

    by thommo59
    Replies
    5
    Views
    333

    Unfortunately I have to agree

    Unfortunately I have to agree
  19. Replies
    6
    Views
    275

    Mine is exactly the same and I thought I ran it...

    Mine is exactly the same and I thought I ran it fairly hard but man those low rpm hours are huge, plus I run salt water 95% so I run on a flusher every time as well
  20. Replies
    6
    Views
    275

    Mine shows hours but I’ve never gone looking for...

    Mine shows hours but I’ve never gone looking for an hours breakdown, I’ll have to check if I can
  21. You either need to add a digital water pressure...

    You either need to add a digital water pressure sender or ensure on the VVM you have chosen water pressure and temp or both
  22. Replies
    6
    Views
    852

    Anyone?

    Anyone?
  23. Replies
    6
    Views
    852

    What sort of PTP are you guys running with the...

    What sort of PTP are you guys running with the Tempest? And what RPM's are you seeing?
  24. Replies
    5
    Views
    492

    Plugs and leads very common but without a service...

    Plugs and leads very common but without a service history could be so many things
  25. Replies
    9
    Views
    391

    There was another post in here almost identical...

    There was another post in here almost identical several months back, you may need to do some searching in this forum
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4