Search:

Type: Posts; User: Nefisherman

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    431

    Now that it’s off, was it just stuck on the...

    Now that it’s off, was it just stuck on the weatherstripping? If so, apply some silicone spray, or something else?
  2. Replies
    6
    Views
    431

    Tried it again and got it, thank you.

    Tried it again and got it, thank you.
  3. Replies
    6
    Views
    431

    Not budging

    Not budging
  4. Replies
    6
    Views
    431

    2015 Optimax pro xs 250 cowl stuck

    I am having a hard time removing my upper cowl from my 2015 pro xs 250. I have had it off several times before but it will not budge. The model number is 1251p73bd and the serial number is 2b123740....
  5. Replies
    2
    Views
    467

    Thank you

    Thank you
  6. Replies
    2
    Views
    467

    Mercury prop hub question

    I am replacing the prop on my optimax which has a mercury flo-torq ii solid hd hub kit. The part number of the hub kit is 840389k06. I know I need to grease the prop shaft/splines but do I also...
  7. Replies
    4
    Views
    350

    What does the recall cover? I have play in my...

    What does the recall cover? I have play in my brackets and all of the hardware is tight, the brackets themselves have play. Is that what the recall takes care of?
  8. Replies
    5
    Views
    1,532

    I have seen everstarts with two different post...

    I have seen everstarts with two different post sizes but the ones I currently have have the same size battery posts, both positive and negative, and they are 5/16-18.
  9. Replies
    14
    Views
    643

    I finally figure out my issue. When I replaced my...

    I finally figure out my issue. When I replaced my terminal block, there were two metal jumpers that fell to the floor. I had never seen these used on a terminal block before and assumed they fell out...
  10. Replies
    0
    Views
    111

    Sea star pro trim lever

    My pro trim lever has a bad switch. It will tilt the motor up but won’t go down. I tested the switch and it is bad. The manufacturer doesn’t offer a replacement switch, they make you buy the whole...
  11. Replies
    14
    Views
    643

    Ok. I’ve made some progress. There are two ground...

    Ok. I’ve made some progress. There are two ground wires at the terminal block under the dash. One is an 8 gauge wire with a red connector which comes straight from the battery negative terminal. The...
  12. Replies
    14
    Views
    643

    Can anyone else verify if my wiring is correct. I...

    Can anyone else verify if my wiring is correct. I have scheduled an appointment at the dealer but they can’t touch the boat for a month.
  13. Replies
    14
    Views
    643

    Mine is a 2016 z20 pro as well. It looks like you...

    Mine is a 2016 z20 pro as well. It looks like you have the two positive wires stacked on one side of the terminal block as well. My boat doesn’t have any remaining wires to put on the opposite side...
  14. Replies
    14
    Views
    643

    I called my local nitro dealer and was told that...

    I called my local nitro dealer and was told that there is no wiring schematic available for my boat. Hopefully someone can help with a picture of the terminal block. My next step is pulling the front...
  15. Replies
    14
    Views
    643

    The battery terminals are clean as are all...

    The battery terminals are clean as are all connectors. I agree that the two red wires don’t look right. I am almost positive that’s how they were. I replaced the terminal block because the screws...
  16. Replies
    14
    Views
    643

    Can anyone tell me if this terminal block wiring...

    Can anyone tell me if this terminal block wiring looks correct?445549
  17. Replies
    14
    Views
    643

    The trim works fine at the shifter and the...

    The trim works fine at the shifter and the steering column. If I hit the trim button on the touch pad at the bow it sometimes does nothing and sometimes won’t stop trimming or tilting until I run...
  18. Replies
    14
    Views
    643

    2016 z20 electrical issue

    Over the winter I installed a new ultrex. When I had the bow panel off I saw that my hydro wave and HDS unit were both powered off of one set of wires split into two to power both from the same...
Results 1 to 18 of 18