Search:

Type: Posts; User: McQuaig

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    38

    on my 2002 the plate bracket hangs down under the...

    on my 2002 the plate bracket hangs down under the left rear trailer step.
  2. Replies
    6
    Views
    228

    Note that there is also a check valve (small...

    Note that there is also a check valve (small ball) in the tank fitting the hose attaches to that could be stuck. Many owners tap out (remove) the ball for less restricted fuel flow. I did on mine, or...
  3. Replies
    6
    Views
    228

    BCB is correct. I recently replaced both pickups...

    BCB is correct. I recently replaced both pickups on my Skeeter. The originals had a mesh "sock" on the bottom. You can buy replacement tubes which include the fitting at top from any marine supplier...
  4. Replies
    15
    Views
    533

    The "float" in that picture iooks like an...

    The "float" in that picture iooks like an electronic one, not a mechanical float....but it does the same job. It likely is the culprit and can be replaced with either type.
  5. You should be able to see or access the troll...

    You should be able to see or access the troll wires by removing the cockpit floor drain cover also.
  6. Replies
    3
    Views
    63

    My 02 is also 6ga. The info is actually pressed...

    My 02 is also 6ga. The info is actually pressed into the wire casing, not printed on, so hard to see.
  7. Just a thought....if your boat is a 2000 Skeeter,...

    Just a thought....if your boat is a 2000 Skeeter, it likely has the small low oil and overheat lights on the dash as well as audible alarm. Any chance the wiring for these somewhere between engine to...
  8. Replies
    10
    Views
    244

    Absolutely possible.

    Absolutely possible.
  9. Replies
    16
    Views
    1,718

    I've done many oil changes on all vehicles and...

    I've done many oil changes on all vehicles and never seen that, but Thank You Very much for posting. I'll definitely look closely from now on...
  10. Thread: gelcoat polish

    by McQuaig
    Replies
    2
    Views
    543

    ok, Thanks. Jescar also makes a "polish" for use...

    ok, Thanks. Jescar also makes a "polish" for use before the sealant to remove minor scratches....
  11. Replies
    5
    Views
    333

    ok, thanks guys....i'll try again

    ok, thanks guys....i'll try again
  12. Thread: gelcoat polish

    by McQuaig
    Replies
    2
    Views
    543

    gelcoat polish

    Has anyone used Jescar Powerlock Polymer Sealant on their glass boat? I see it very highly rated on auto/marine detailing sites. Any feedback would be appreciated. Thanks
  13. Although the up relay is clicking, it's worth a...

    Although the up relay is clicking, it's worth a try to swap the up and down relays just to be sure it's not a "weak" one....
  14. Replies
    5
    Views
    333

    Pro-Tec Sealant

    Does anyone know if Pro-tec is still going? My email to them gets denied and also no answer on either phone number. Thanks
  15. Replies
    7
    Views
    267

    On my 02 ZX there are 4 screws at very bottom of...

    On my 02 ZX there are 4 screws at very bottom of seat backs. Remove those, then lift straight up out of the hidden bracket behind. The bottoms (if not hinged) will likely be attached by screws in...
  16. Replies
    4
    Views
    317

    The gauge doesn't need power (only for the...

    The gauge doesn't need power (only for the light). Yes you can blow into it but not really hard as too much pressure will wreck it.
  17. Replies
    19
    Views
    803

    Yes, seems to me like the way you're sealing it...

    Yes, seems to me like the way you're sealing it should work fine, especially if there's no wood in transom. Only other thing I can think of is water getting somewhere else? My brother's aluminum boat...
  18. Replies
    19
    Views
    803

    I may be way off, but is it possible your plate...

    I may be way off, but is it possible your plate is installed backwards? I had one of these years ago and I'm pretty sure mine had the slots on engine side. That made it easy to change engine mount by...
  19. Replies
    19
    Views
    803

    I've never seen a jackplate with "slots" for the...

    I've never seen a jackplate with "slots" for the mounting bolts on transom side. Do you have a pic of it?
  20. Replies
    5
    Views
    360

    Also replace spark plugs....the correct...

    Also replace spark plugs....the correct replacement ones are much cheaper at local auto parts store than Yamaha dealer. I also change my fuel filter and water sep filter every year, and inspect...
  21. Possibly just a plugged telltale hose. Either use...

    Possibly just a plugged telltale hose. Either use a wire to clean it or disconnect it and blow it out into a towel to see what comes out...
  22. Replies
    8
    Views
    374

    Here's the wire color coding from my 2002 if it...

    Here's the wire color coding from my 2002 if it helps..
    .541953.Note: Port Fill and Stbd Fill are the livewells.
  23. Replies
    16
    Views
    480

    My 330pc took forever to charge batteries. I read...

    My 330pc took forever to charge batteries. I read a post here that an ext cord with no ground post could affect charge times. Sure enough, I replaced my ext cord with a good one and now charges in...
  24. Replies
    7
    Views
    485

    Bass boat fuel tanks are designed/located by the...

    Bass boat fuel tanks are designed/located by the manufacturer for best weight distribution (for best ride), at the same time being able to fit in all the batteries and livewells. That's also why we...
  25. Replies
    7
    Views
    485

    Bass boat fuel tanks are designed/located by the...

    Bass boat fuel tanks are designed/located by the manufacturer for best weight distribution (for best ride), at the same time being able to fit in all the batteries and livewells. That's also why we...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4